* [PATCH 2/6] motion: update to 4.0.1
2016-11-13 19:23 [PATCH 0/6] Update ffmepg and the packages that use it Marcel Lorenz
2016-11-13 19:23 ` [PATCH 1/6] ffmpeg and ffmpeg-libs: update 3.1.4 Marcel Lorenz
@ 2016-11-13 19:23 ` Marcel Lorenz
2016-11-13 19:23 ` [PATCH 3/6] xvid: update to 1.3.4 Marcel Lorenz
` (3 subsequent siblings)
5 siblings, 0 replies; 11+ messages in thread
From: Marcel Lorenz @ 2016-11-13 19:23 UTC (permalink / raw)
To: development
[-- Attachment #1: Type: text/plain, Size: 49509 bytes --]
Signed-off-by: Marcel Lorenz <marcel.lorenz(a)ipfire.org>
---
config/motion/camera1.conf | 71 +++++++
config/motion/camera2.conf | 71 +++++++
config/motion/camera3.conf | 71 +++++++
config/motion/camera4.conf | 71 +++++++
config/motion/motion.conf | 447 +++++++++++++++++++++++++--------------
config/rootfiles/packages/motion | 50 ++---
lfs/motion | 26 +--
7 files changed, 610 insertions(+), 197 deletions(-)
create mode 100644 config/motion/camera1.conf
create mode 100644 config/motion/camera2.conf
create mode 100644 config/motion/camera3.conf
create mode 100644 config/motion/camera4.conf
diff --git a/config/motion/camera1.conf b/config/motion/camera1.conf
new file mode 100644
index 0000000..505c609
--- /dev/null
+++ b/config/motion/camera1.conf
@@ -0,0 +1,71 @@
+# /etc/motion/camera1.conf
+#
+# This config file was generated by motion 4.0.1
+
+###########################################################
+# Capture device options
+############################################################
+
+# Camera Id
+# Consistent identification number to assign to each camera across multiple
+# invocations of Motion.
+# Default: The order when the camera file was read
+# camera_id = 1
+
+# Videodevice to be used for capturing (default /dev/video0)
+# for FreeBSD default is /dev/bktr0
+videodevice /dev/video0
+
+# The video input to be used (default: -1)
+# Should normally be set to 1 for video/TV cards, and -1 for USB cameras
+input -1
+
+# Draw a user defined text on the images using same options as C function strftime(3)
+# Default: Not defined = no text
+# Text is placed in lower left corner
+text_left CAMERA 1
+
+
+############################################################
+# Target Directories and filenames For Images And Films
+# For the options snapshot_, picture_, mpeg_ and timelapse_filename
+# you can use conversion specifiers
+# %Y = year, %m = month, %d = date,
+# %H = hour, %M = minute, %S = second,
+# %v = event, %q = frame number, %t = camera id number,
+# %D = changed pixels, %N = noise level,
+# %i and %J = width and height of motion area,
+# %K and %L = X and Y coordinates of motion center
+# %C = value defined by text_event
+# Quotation marks round string are allowed.
+############################################################
+
+# Target base directory for pictures and films
+# Recommended to use absolute patch. (Default: current working directory)
+#target_dir /tmp/motion/cam1
+
+# File path for motion triggered images (jpeg or ppm) relative to target_dir
+# Default: %v-%Y%m%d%H%M%S-%q
+# Default value is equivalent to legacy oldlayout option
+# For Motion 3.0 compatible mode choose: %Y/%m/%d/%H/%M/%S-%q
+# File extension .jpg or .ppm is automatically added so do not include this
+# Set to 'preview' together with best-preview feature enables special naming
+# convention for preview shots. See motion guide for details
+picture_filename CAM1_%v-%Y%m%d%H%M%S-%q
+
+
+############################################################
+# Live Stream Server
+############################################################
+
+# The mini-http server listens to this port for requests (default: 0 = disabled)
+stream_port 8081
+
+# Command to be executed when a picture (.ppm|.jpg) is saved (default: none)
+# The filename of the picture is appended as an argument for the command.
+#on_picture_save /usr/local/motion-extras/camparse2.pl
+
+# Command to be executed when a movie file (.mpg|.avi) is closed. (default: none)
+# Filename of movie is appended as an argument for the command.
+#on_movie_end /usr/local/motion-extras/mpegparse2.pl
+
diff --git a/config/motion/camera2.conf b/config/motion/camera2.conf
new file mode 100644
index 0000000..6c897b1
--- /dev/null
+++ b/config/motion/camera2.conf
@@ -0,0 +1,71 @@
+# /etc/motion/camera2.conf
+#
+# This config file was generated by motion 4.0.1
+
+###########################################################
+# Capture device options
+############################################################
+
+# Camera Id
+# Consistent identification number to assign to each camera across multiple
+# invocations of Motion.
+# Default: The order when the camera file was read
+# camera_id = 2
+
+# Videodevice to be used for capturing (default /dev/video0)
+# for FreeBSD default is /dev/bktr0
+videodevice /dev/video1
+
+# The video input to be used (default: -1)
+# Should normally be set to 1 for video/TV cards, and -1 for USB cameras
+input 1
+
+# Draw a user defined text on the images using same options as C function strftime(3)
+# Default: Not defined = no text
+# Text is placed in lower left corner
+text_left CAMERA 2
+
+
+############################################################
+# Target Directories and filenames For Images And Films
+# For the options snapshot_, picture_, mpeg_ and timelapse_filename
+# you can use conversion specifiers
+# %Y = year, %m = month, %d = date,
+# %H = hour, %M = minute, %S = second,
+# %v = event, %q = frame number, %t = camera id number,
+# %D = changed pixels, %N = noise level,
+# %i and %J = width and height of motion area,
+# %K and %L = X and Y coordinates of motion center
+# %C = value defined by text_event
+# Quotation marks round string are allowed.
+############################################################
+
+# Target base directory for pictures and films
+# Recommended to use absolute patch. (Default: current working directory)
+#target_dir /tmp/motion/cam2
+
+# File path for motion triggered images (jpeg or ppm) relative to target_dir
+# Default: %v-%Y%m%d%H%M%S-%q
+# Default value is equivalent to legacy oldlayout option
+# For Motion 3.0 compatible mode choose: %Y/%m/%d/%H/%M/%S-%q
+# File extension .jpg or .ppm is automatically added so do not include this
+# Set to 'preview' together with best-preview feature enables special naming
+# convention for preview shots. See motion guide for details
+picture_filename CAM2_%v-%Y%m%d%H%M%S-%q
+
+
+############################################################
+# Live Stream Server
+############################################################
+
+# The mini-http server listens to this port for requests (default: 0 = disabled)
+stream_port 8082
+
+# Command to be executed when a picture (.ppm|.jpg) is saved (default: none)
+# The filename of the picture is appended as an argument for the command.
+#on_picture_save /usr/local/motion-extras/camparse2.pl
+
+# Command to be executed when a movie file (.mpg|.avi) is closed. (default: none)
+# Filename of movie is appended as an argument for the command.
+#on_movie_end /usr/local/motion-extras/mpegparse2.pl
+
diff --git a/config/motion/camera3.conf b/config/motion/camera3.conf
new file mode 100644
index 0000000..da9a52f
--- /dev/null
+++ b/config/motion/camera3.conf
@@ -0,0 +1,71 @@
+# /etc/motion/camera3.conf
+#
+# This config file was generated by motion 4.0.1
+
+###########################################################
+# Capture device options
+############################################################
+
+# Camera Id
+# Consistent identification number to assign to each camera across multiple
+# invocations of Motion.
+# Default: The order when the camera file was read
+# camera_id = 3
+
+# Videodevice to be used for capturing (default /dev/video0)
+# for FreeBSD default is /dev/bktr0
+videodevice /dev/video2
+
+# The video input to be used (default: -1)
+# Should normally be set to 1 for video/TV cards, and -1 for USB cameras
+input -1
+
+# Draw a user defined text on the images using same options as C function strftime(3)
+# Default: Not defined = no text
+# Text is placed in lower left corner
+text_left CAMERA 3
+
+
+############################################################
+# Target Directories and filenames For Images And Films
+# For the options snapshot_, picture_, mpeg_ and timelapse_filename
+# you can use conversion specifiers
+# %Y = year, %m = month, %d = date,
+# %H = hour, %M = minute, %S = second,
+# %v = event, %q = frame number, %t = camera id number,
+# %D = changed pixels, %N = noise level,
+# %i and %J = width and height of motion area,
+# %K and %L = X and Y coordinates of motion center
+# %C = value defined by text_event
+# Quotation marks round string are allowed.
+############################################################
+
+# Target base directory for pictures and films
+# Recommended to use absolute patch. (Default: current working directory)
+#target_dir /tmp/motion/cam3
+
+# File path for motion triggered images (jpeg or ppm) relative to target_dir
+# Default: %v-%Y%m%d%H%M%S-%q
+# Default value is equivalent to legacy oldlayout option
+# For Motion 3.0 compatible mode choose: %Y/%m/%d/%H/%M/%S-%q
+# File extension .jpg or .ppm is automatically added so do not include this
+# Set to 'preview' together with best-preview feature enables special naming
+# convention for preview shots. See motion guide for details
+picture_filename CAM3_%v-%Y%m%d%H%M%S-%q
+
+
+############################################################
+# Live Stream Server
+############################################################
+
+# The mini-http server listens to this port for requests (default: 0 = disabled)
+stream_port 8083
+
+# Command to be executed when a picture (.ppm|.jpg) is saved (default: none)
+# The filename of the picture is appended as an argument for the command.
+#on_picture_save /usr/local/motion-extras/camparse2.pl
+
+# Command to be executed when a movie file (.mpg|.avi) is closed. (default: none)
+# Filename of movie is appended as an argument for the command.
+#on_movie_end /usr/local/motion-extras/mpegparse2.pl
+
diff --git a/config/motion/camera4.conf b/config/motion/camera4.conf
new file mode 100644
index 0000000..da94f40
--- /dev/null
+++ b/config/motion/camera4.conf
@@ -0,0 +1,71 @@
+# /etc/motion/camera4.conf
+#
+# This config file was generated by motion 4.0.1
+
+###########################################################
+# Capture device options
+############################################################
+
+# Camera Id
+# Consistent identification number to assign to each camera across multiple
+# invocations of Motion.
+# Default: The order when the camera file was read
+# camera_id = 4
+
+# Videodevice to be used for capturing (default /dev/video0)
+# for FreeBSD default is /dev/bktr0
+videodevice /dev/video3
+
+# The video input to be used (default: -1)
+# Should normally be set to 1 for video/TV cards, and -1 for USB cameras
+input -1
+
+# Draw a user defined text on the images using same options as C function strftime(3)
+# Default: Not defined = no text
+# Text is placed in lower left corner
+text_left CAMERA 4
+
+
+############################################################
+# Target Directories and filenames For Images And Films
+# For the options snapshot_, picture_, mpeg_ and timelapse_filename
+# you can use conversion specifiers
+# %Y = year, %m = month, %d = date,
+# %H = hour, %M = minute, %S = second,
+# %v = event, %q = frame number, %t = camera id number,
+# %D = changed pixels, %N = noise level,
+# %i and %J = width and height of motion area,
+# %K and %L = X and Y coordinates of motion center
+# %C = value defined by text_event
+# Quotation marks round string are allowed.
+############################################################
+
+# Target base directory for pictures and films
+# Recommended to use absolute patch. (Default: current working directory)
+#target_dir /tmp/motion/cam4
+
+# File path for motion triggered images (jpeg or ppm) relative to target_dir
+# Default: %v-%Y%m%d%H%M%S-%q
+# Default value is equivalent to legacy oldlayout option
+# For Motion 3.0 compatible mode choose: %Y/%m/%d/%H/%M/%S-%q
+# File extension .jpg or .ppm is automatically added so do not include this
+# Set to 'preview' together with best-preview feature enables special naming
+# convention for preview shots. See motion guide for details
+picture_filename CAM4_%v-%Y%m%d%H%M%S-%q
+
+
+############################################################
+# Live Stream Server
+############################################################
+
+# The mini-http server listens to this port for requests (default: 0 = disabled)
+stream_port 8084
+
+# Command to be executed when a picture (.ppm|.jpg) is saved (default: none)
+# The filename of the picture is appended as an argument for the command.
+#on_picture_save /usr/local/motion-extras/camparse2.pl
+
+# Command to be executed when a movie file (.mpg|.avi) is closed. (default: none)
+# Filename of movie is appended as an argument for the command.
+#on_movie_end /usr/local/motion-extras/mpegparse2.pl
+
diff --git a/config/motion/motion.conf b/config/motion/motion.conf
index 0d2853a..22cb76e 100644
--- a/config/motion/motion.conf
+++ b/config/motion/motion.conf
@@ -1,6 +1,6 @@
# Rename this distribution example file to motion.conf
#
-# This config file was generated by motion 3.2.11
+# This config file was generated by motion 4.0.1
############################################################
@@ -8,10 +8,10 @@
############################################################
# Start in daemon (background) mode and release terminal (default: off)
-daemon on
+daemon off
# File to store the process ID, also called pid file. (default: not defined)
-process_id_file /var/run/motion.pid
+process_id_file /var/run/motion/motion.pid
############################################################
# Basic Setup Mode
@@ -20,6 +20,16 @@ process_id_file /var/run/motion.pid
# Start in Setup-Mode, daemon disabled. (default: off)
setup_mode off
+
+# Use a file to save logs messages, if not defined stderr and syslog is used. (default: not defined)
+;logfile /tmp/motion.log
+
+# Level of log messages [1..9] (EMG, ALR, CRT, ERR, WRN, NTC, INF, DBG, ALL). (default: 6 / NTC)
+log_level 6
+
+# Filter to log messages by type (COR, STR, ENC, NET, DBL, EVT, TRK, VID, ALL). (default: ALL)
+log_type all
+
###########################################################
# Capture device options
############################################################
@@ -28,32 +38,43 @@ setup_mode off
# for FreeBSD default is /dev/bktr0
videodevice /dev/video0
-# v4l2_palette allows to choose preferable palette to be use by motion
-# to capture from those supported by your videodevice. (default: 8)
+# v4l2_palette allows one to choose preferable palette to be use by motion
+# to capture from those supported by your videodevice. (default: 17)
# E.g. if your videodevice supports both V4L2_PIX_FMT_SBGGR8 and
# V4L2_PIX_FMT_MJPEG then motion will by default use V4L2_PIX_FMT_MJPEG.
-# Setting v4l2_palette to 1 forces motion to use V4L2_PIX_FMT_SBGGR8
+# Setting v4l2_palette to 2 forces motion to use V4L2_PIX_FMT_SBGGR8
# instead.
#
# Values :
# V4L2_PIX_FMT_SN9C10X : 0 'S910'
-# V4L2_PIX_FMT_SBGGR8 : 1 'BA81'
-# V4L2_PIX_FMT_MJPEG : 2 'MJPEG'
-# V4L2_PIX_FMT_JPEG : 3 'JPEG'
-# V4L2_PIX_FMT_RGB24 : 4 'RGB3'
-# V4L2_PIX_FMT_UYVY : 5 'UYVY'
-# V4L2_PIX_FMT_YUYV : 6 'YUYV'
-# V4L2_PIX_FMT_YUV422P : 7 '422P'
-# V4L2_PIX_FMT_YUV420 : 8 'YU12'
-v4l2_palette 8
+# V4L2_PIX_FMT_SBGGR16 : 1 'BYR2'
+# V4L2_PIX_FMT_SBGGR8 : 2 'BA81'
+# V4L2_PIX_FMT_SPCA561 : 3 'S561'
+# V4L2_PIX_FMT_SGBRG8 : 4 'GBRG'
+# V4L2_PIX_FMT_SGRBG8 : 5 'GRBG'
+# V4L2_PIX_FMT_PAC207 : 6 'P207'
+# V4L2_PIX_FMT_PJPG : 7 'PJPG'
+# V4L2_PIX_FMT_MJPEG : 8 'MJPEG'
+# V4L2_PIX_FMT_JPEG : 9 'JPEG'
+# V4L2_PIX_FMT_RGB24 : 10 'RGB3'
+# V4L2_PIX_FMT_SPCA501 : 11 'S501'
+# V4L2_PIX_FMT_SPCA505 : 12 'S505'
+# V4L2_PIX_FMT_SPCA508 : 13 'S508'
+# V4L2_PIX_FMT_UYVY : 14 'UYVY'
+# V4L2_PIX_FMT_YUYV : 15 'YUYV'
+# V4L2_PIX_FMT_YUV422P : 16 '422P'
+# V4L2_PIX_FMT_YUV420 : 17 'YU12'
+#
+v4l2_palette 17
# Tuner device to be used for capturing using tuner as source (default /dev/tuner0)
# This is ONLY used for FreeBSD. Leave it commented out for Linux
; tunerdevice /dev/tuner0
-# The video input to be used (default: 8)
-# Should normally be set to 0 or 1 for video/TV cards, and 8 for USB cameras
-input 8
+# The video input to be used (default: -1)
+# Should normally be set to 0 or 1 for video/TV cards, and -1 for USB cameras
+# Set to 0 for uvideo(4) on OpenBSD
+input -1
# The video norm to use (only for video capture and TV tuner cards)
# Values: 0 (PAL), 1 (NTSC), 2 (SECAM), 3 (PAL NC no colour). Default: 0 (PAL)
@@ -62,8 +83,17 @@ norm 0
# The frequency to set the tuner to (kHz) (only for TV tuner cards) (default: 0)
frequency 0
+# Override the power line frequency for the webcam. (normally not necessary)
+# Values:
+# -1 : Do not modify device setting
+# 0 : Power line frequency Disabled
+# 1 : 50hz
+# 2 : 60hz
+# 3 : Auto
+power_line_frequency -1
+
# Rotate image this number of degrees. The rotation affects all saved images as
-# well as mpeg movies. Valid values: 0 (default = no rotation), 90, 180 and 270.
+# well as movies. Valid values: 0 (default = no rotation), 90, 180 and 270.
rotate 0
# Image width (pixels). Valid range: Camera dependent, default: 352
@@ -81,8 +111,9 @@ framerate 2
# This option is used when you want to capture images at a rate lower than 2 per second.
minimum_frame_time 0
-# URL to use if you are using a network camera, size will be autodetected (incl http:// ftp:// or file:///)
-# Must be a URL that returns single jpeg pictures or a raw mjpeg stream. Default: Not defined
+# URL to use if you are using a network camera, size will be autodetected (incl http:// ftp:// mjpg:// rtsp:// mjpeg:// or file:///)
+# Must be a URL that returns single jpeg pictures or a raw mjpeg stream. A trailing slash may be required for some cameras.
+# Default: Not defined
; netcam_url value
# Username and password for network camera (only if required). Default: not defined
@@ -90,32 +121,44 @@ minimum_frame_time 0
; netcam_userpass value
# The setting for keep-alive of network socket, should improve performance on compatible net cameras.
-# 1.0: The historical implementation using HTTP/1.0, closing the socket after each http request.
-# keep_alive: Use HTTP/1.0 requests with keep alive header to reuse the same connection.
-# 1.1: Use HTTP/1.1 requests that support keep alive as default.
-# Default: 1.0
-; netcam_http 1.0
+# off: The historical implementation using HTTP/1.0, closing the socket after each http request.
+# force: Use HTTP/1.0 requests with keep alive header to reuse the same connection.
+# on: Use HTTP/1.1 requests that support keep alive as default.
+# Default: off
+netcam_keepalive off
# URL to use for a netcam proxy server, if required, e.g. "http://myproxy".
# If a port number other than 80 is needed, use "http://myproxy:1234".
# Default: not defined
-; netcam_proxy value
+; netcam_proxy value
# Set less strict jpeg checks for network cameras with a poor/buggy firmware.
# Default: off
netcam_tolerant_check off
+# RTSP connection uses TCP to communicate to the camera. Can prevent image corruption.
+# Default: on
+rtsp_uses_tcp on
+
+# Name of camera to use if you are using a camera accessed through OpenMax/MMAL
+# Default: Not defined
+; mmalcam_name vc.ril.camera
+
+# Camera control parameters (see raspivid/raspistill tool documentation)
+# Default: Not defined
+; mmalcam_control_params -hf
+
# Let motion regulate the brightness of a video device (default: off).
# The auto_brightness feature uses the brightness option as its target value.
# If brightness is zero auto_brightness will adjust to average brightness value 128.
# Only recommended for cameras without auto brightness
-auto_brightness on
+auto_brightness off
# Set the initial brightness of a video device.
# If auto_brightness is enabled, this value defines the average brightness level
# which Motion will try and adjust to.
# Valid range 0-255, default 0 = disabled
-brightness 128
+brightness 0
# Set the contrast of a video device.
# Valid range 0-255, default 0 = disabled
@@ -165,12 +208,13 @@ noise_tune on
# Recommended value is EedDl. Any combination (and number of) of E, e, d, and D is valid.
# (l)abeling must only be used once and the 'l' must be the last letter.
# Comment out to disable
-despeckle EedDl
+despeckle_filter EedDl
# Detect motion in predefined areas (1 - 9). Areas are numbered like that: 1 2 3
# A script (on_area_detected) is started immediately when motion is 4 5 6
# detected in one of the given areas, but only once during an event. 7 8 9
-# One or more areas can be specified with this option. (Default: not defined)
+# One or more areas can be specified with this option. Take care: This option
+# does NOT restrict detection to these areas! (Default: not defined)
; area_detect value
# PGM file to use as a sensitivity mask.
@@ -194,24 +238,26 @@ minimum_motion_frames 1
# was detected that will be output at motion detection.
# Recommended range: 0 to 5 (default: 0)
# Do not use large values! Large values will cause Motion to skip video frames and
-# cause unsmooth mpegs. To smooth mpegs use larger values of post_capture instead.
-pre_capture 5
+# cause unsmooth movies. To smooth movies use larger values of post_capture instead.
+pre_capture 2
# Number of frames to capture after motion is no longer detected (default: 0)
-post_capture 5
+post_capture 2
-# Gap is the seconds of no motion detection that triggers the end of an event
+# Event Gap is the seconds of no motion detection that triggers the end of an event.
# An event is defined as a series of motion images taken within a short timeframe.
-# Recommended value is 60 seconds (Default). The value 0 is allowed and disables
-# events causing all Motion to be written to one single mpeg file and no pre_capture.
-gap 0
+# Recommended value is 60 seconds (Default). The value -1 is allowed and disables
+# events causing all Motion to be written to one single movie file and no pre_capture.
+# If set to 0, motion is running in gapless mode. Movies don't have gaps anymore. An
+# event ends right after no more motion is detected and post_capture is over.
+event_gap 60
-# Maximum length in seconds of an mpeg movie
-# When value is exceeded a new mpeg file is created. (Default: 0 = infinite)
-max_mpeg_time 86400
+# Maximum length in seconds of a movie
+# When value is exceeded a new movie file is created. (Default: 0 = infinite)
+max_movie_time 0
# Always save images even if there was no motion (default: off)
-output_all off
+emulate_motion off
############################################################
@@ -224,33 +270,33 @@ output_all off
# Picture with most motion of an event is saved when set to 'best'.
# Picture with motion nearest center of picture is saved when set to 'center'.
# Can be used as preview shot for the corresponding movie.
-output_normal off
+output_pictures on
# Output pictures with only the pixels moving object (ghost images) (default: off)
-output_motion off
+output_debug_pictures off
# The quality (in percent) to be used by the jpeg compression (default: 75)
quality 75
-# Output ppm images instead of jpeg (default: off)
-ppm off
-
+# Type of output images
+# Valid values: jpeg, ppm (default: jpeg)
+picture_type jpeg
############################################################
# FFMPEG related options
-# Film (mpeg) file output, and deinterlacing of the video input
+# Film (movies) file output, and deinterlacing of the video input
# The options movie_filename and timelapse_filename are also used
# by the ffmpeg feature
############################################################
-# Use ffmpeg to encode mpeg movies in realtime (default: off)
-ffmpeg_cap_new off
+# Use ffmpeg to encode movies in realtime (default: off)
+ffmpeg_output_movies on
# Use ffmpeg to make movies with only the pixels moving
# object (ghost images) (default: off)
-ffmpeg_cap_motion off
+ffmpeg_output_debug_movies off
-# Use ffmpeg to encode a timelapse movie
+# Use ffmpeg to encode a timelapse movie
# Default value 0 = off - else save frame every Nth second
ffmpeg_timelapse 0
@@ -260,31 +306,63 @@ ffmpeg_timelapse_mode daily
# Bitrate to be used by the ffmpeg encoder (default: 400000)
# This option is ignored if ffmpeg_variable_bitrate is not 0 (disabled)
-ffmpeg_bps 500000
+ffmpeg_bps 400000
# Enables and defines variable bitrate for the ffmpeg encoder.
# ffmpeg_bps is ignored if variable bitrate is enabled.
# Valid values: 0 (default) = fixed bitrate defined by ffmpeg_bps,
-# or the range 2 - 31 where 2 means best quality and 31 is worst.
+# or the range 1 - 100 where 1 means worst quality and 100 is best.
ffmpeg_variable_bitrate 0
# Codec to used by ffmpeg for the video compression.
-# Timelapse mpegs are always made in mpeg1 format independent from this option.
-# Supported formats are: mpeg1 (ffmpeg-0.4.8 only), mpeg4 (default), and msmpeg4.
-# mpeg1 - gives you files with extension .mpg
+# Timelapse videos have two options.
+# mpg - Creates mpg file with mpeg-2 encoding.
+# If motion is shutdown and restarted, new pics will be appended
+# to any previously created file with name indicated for timelapse.
+# mpeg4 - Creates avi file with the default encoding.
+# If motion is shutdown and restarted, new pics will create a
+# new file with the name indicated for timelapse.
+# Supported formats are:
# mpeg4 or msmpeg4 - gives you files with extension .avi
# msmpeg4 is recommended for use with Windows Media Player because
# it requires no installation of codec on the Windows client.
# swf - gives you a flash film with extension .swf
# flv - gives you a flash video with extension .flv
-# ffv1 - FF video codec 1 for Lossless Encoding ( experimental )
-# mov - QuickTime ( testing )
-ffmpeg_video_codec msmpeg4
+# ffv1 - FF video codec 1 for Lossless Encoding
+# mov - QuickTime
+# mp4 - MPEG-4 Part 14 H264 encoding
+# mkv - Matroska H264 encoding
+# hevc - H.265 / HEVC (High Efficiency Video Coding)
+ffmpeg_video_codec mpeg4
-# Use ffmpeg to deinterlace video. Necessary if you use an analog camera
-# and see horizontal combing on moving objects in video or pictures.
-# (default: off)
-ffmpeg_deinterlace off
+# When creating videos, should frames be duplicated in order
+# to keep up with the requested frames per second
+# (default: true)
+ffmpeg_duplicate_frames true
+
+############################################################
+# SDL Window
+############################################################
+
+# Number of motion thread to show in SDL Window (default: 0 = disabled)
+#sdl_threadnr 0
+
+############################################################
+# External pipe to video encoder
+# Replacement for FFMPEG builtin encoder for ffmpeg_output_movies only.
+# The options movie_filename and timelapse_filename are also used
+# by the ffmpeg feature
+#############################################################
+
+# Bool to enable or disable extpipe (default: off)
+use_extpipe off
+
+# External program (full path and opts) to pipe raw video to
+# Generally, use '-' for STDIN...
+;extpipe mencoder -demuxer rawvideo -rawvideo w=%w:h=%h:i420 -ovc x264 -x264encopts bframes=4:frameref=1:subq=1:scenecut=-1:nob_adapt:threads=1:keyint=1000:8x8dct:vbv_bufsize=4000:crf=24:partitions=i8x8,i4x4:vbv_maxrate=800:no-chroma-me -vf denoise3d=16:12:48:4,pp=lb -of avi -o %f.avi - -fps %fps
+;extpipe x264 - --input-res %wx%h --fps %fps --bitrate 2000 --preset ultrafast --quiet -o %f.mp4
+;extpipe mencoder -demuxer rawvideo -rawvideo w=%w:h=%h:fps=%fps -ovc x264 -x264encopts preset=ultrafast -of lavf -o %f.mp4 - -fps %fps
+;extpipe ffmpeg -y -f rawvideo -pix_fmt yuv420p -video_size %wx%h -framerate %fps -i pipe:0 -vcodec libx264 -preset ultrafast -f mp4 %f.mp4
############################################################
@@ -299,7 +377,7 @@ snapshot_interval 0
# Text Display
# %Y = year, %m = month, %d = date,
# %H = hour, %M = minute, %S = second, %T = HH:MM:SS,
-# %v = event, %q = frame number, %t = thread (camera) number,
+# %v = event, %q = frame number, %t = camera id number,
# %D = changed pixels, %N = noise level, \n = new line,
# %i and %J = width and height of motion area,
# %K and %L = X and Y coordinates of motion center
@@ -309,9 +387,17 @@ snapshot_interval 0
############################################################
# Locate and draw a box around the moving object.
-# Valid values: on, off and preview (default: off)
+# Valid values: on, off, preview (default: off)
# Set to 'preview' will only draw a box in preview_shot pictures.
-locate off
+locate_motion_mode off
+
+# Set the look and style of the locate box if enabled.
+# Valid values: box, redbox, cross, redcross (default: box)
+# Set to 'box' will draw the traditional box.
+# Set to 'redbox' will draw a red box.
+# Set to 'cross' will draw a little cross to mark center.
+# Set to 'redcross' will draw a little red cross to mark center.
+locate_motion_style box
# Draws the timestamp using same options as C function strftime(3)
# Default: %Y-%m-%d\n%T = date in ISO format and time in 24 hour clock
@@ -321,7 +407,7 @@ text_right %Y-%m-%d\n%T-%q
# Draw a user defined text on the images using same options as C function strftime(3)
# Default: Not defined = no text
# Text is placed in lower left corner
-text_left CAMERA %t\nhttp://www.ipfire.org
+; text_left CAMERA %t
# Draw the number of changed pixed on the images (default: off)
# Will normally be set to off except when you setup and adjust the motion settings
@@ -340,13 +426,18 @@ text_event %Y%m%d%H%M%S
text_double off
+# Text to include in a JPEG EXIF comment
+# May be any text, including conversion specifiers.
+# The EXIF timestamp is included independent of this text.
+;exif_text %i%J/%K%L
+
############################################################
# Target Directories and filenames For Images And Films
-# For the options snapshot_, jpeg_, mpeg_ and timelapse_filename
+# For the options snapshot_, picture_, movie_ and timelapse_filename
# you can use conversion specifiers
# %Y = year, %m = month, %d = date,
# %H = hour, %M = minute, %S = second,
-# %v = event, %q = frame number, %t = thread (camera) number,
+# %v = event, %q = frame number, %t = camera id number,
# %D = changed pixels, %N = noise level,
# %i and %J = width and height of motion area,
# %K and %L = X and Y coordinates of motion center
@@ -356,7 +447,7 @@ text_double off
# Target base directory for pictures and films
# Recommended to use absolute path. (Default: current working directory)
-target_dir /var/motion/cam1
+#target_dir /tmp/motion
# File path for snapshots (jpeg or ppm) relative to target_dir
# Default: %v-%Y%m%d%H%M%S-snapshot
@@ -374,73 +465,90 @@ snapshot_filename %v-%Y%m%d%H%M%S-snapshot
# File extension .jpg or .ppm is automatically added so do not include this
# Set to 'preview' together with best-preview feature enables special naming
# convention for preview shots. See motion guide for details
-jpeg_filename %v-%Y%m%d%H%M%S-%q
+picture_filename %v-%Y%m%d%H%M%S-%q
-# File path for motion triggered ffmpeg films (mpeg) relative to target_dir
+# File path for motion triggered ffmpeg films (movies) relative to target_dir
# Default: %v-%Y%m%d%H%M%S
-# Default value is equivalent to legacy oldlayout option
-# For Motion 3.0 compatible mode choose: %Y/%m/%d/%H%M%S
-# File extension .mpg or .avi is automatically added so do not include this
-# This option was previously called ffmpeg_filename
+# File extensions(.mpg .avi) are automatically added so do not include them
movie_filename %v-%Y%m%d%H%M%S
-# File path for timelapse mpegs relative to target_dir
+# File path for timelapse movies relative to target_dir
# Default: %Y%m%d-timelapse
-# Default value is near equivalent to legacy oldlayout option
-# For Motion 3.0 compatible mode choose: %Y/%m/%d-timelapse
-# File extension .mpg is automatically added so do not include this
+# File extensions(.mpg .avi) are automatically added so do not include them
timelapse_filename %Y%m%d-timelapse
+############################################################
+# Global Network Options
+############################################################
+# Enable IPv6 (default: off)
+ipv6_enabled off
############################################################
-# Live Webcam Server
+# Live Stream Server
############################################################
# The mini-http server listens to this port for requests (default: 0 = disabled)
-webcam_port 2500
+stream_port 8081
-# Quality of the jpeg images produced (default: 50)
-webcam_quality 50
+# Quality of the jpeg (in percent) images produced (default: 50)
+stream_quality 50
# Output frames at 1 fps when no motion is detected and increase to the
-# rate given by webcam_maxrate when motion is detected (default: off)
-webcam_motion off
+# rate given by stream_maxrate when motion is detected (default: off)
+stream_motion off
-# Maximum framerate for webcam streams (default: 1)
-webcam_maxrate 1
+# Maximum framerate for stream streams (default: 1)
+stream_maxrate 1
-# Restrict webcam connections to localhost only (default: on)
-webcam_localhost off
+# Restrict stream connections to localhost only (default: on)
+stream_localhost on
# Limits the number of images per connection (default: 0 = unlimited)
-# Number can be defined by multiplying actual webcam rate by desired number of seconds
-# Actual webcam rate is the smallest of the numbers framerate and webcam_maxrate
-webcam_limit 0
+# Number can be defined by multiplying actual stream rate by desired number of seconds
+# Actual stream rate is the smallest of the numbers framerate and stream_maxrate
+stream_limit 0
+# Set the authentication method (default: 0)
+# 0 = disabled
+# 1 = Basic authentication
+# 2 = MD5 digest (the safer authentication)
+stream_auth_method 0
+
+# Authentication for the stream. Syntax username:password
+# Default: not defined (Disabled)
+; stream_authentication username:password
+
+# Percentage to scale the stream image for preview
+# Default: 25
+; stream_preview_scale 25
+
+# Have stream preview image start on a new line
+# Default: no
+; stream_preview_newline no
############################################################
# HTTP Based Control
############################################################
# TCP/IP port for the http server to listen on (default: 0 = disabled)
-control_port 0
+webcontrol_port 8080
# Restrict control connections to localhost only (default: on)
-control_localhost on
+webcontrol_localhost on
# Output for http server, select off to choose raw text plain (default: on)
-control_html_output on
+webcontrol_html_output on
# Authentication for the http based control. Syntax username:password
# Default: not defined (Disabled)
-; control_authentication username:password
+; webcontrol_authentication username:password
############################################################
# Tracking (Pan/Tilt)
-############################################################
+#############################################################
-# Type of tracker (0=none (default), 1=stepper, 2=iomojo, 3=pwc, 4=generic, 5=uvcvideo)
+# Type of tracker (0=none (default), 1=stepper, 2=iomojo, 3=pwc, 4=generic, 5=uvcvideo, 6=servo)
# The generic type enables the definition of motion center and motion size to
# be used with the conversion specifiers for options like on_motion_detected
track_type 0
@@ -449,19 +557,37 @@ track_type 0
track_auto off
# Serial port of motor (default: none)
-; track_port value
+;track_port /dev/ttyS0
# Motor number for x-axis (default: 0)
-track_motorx 0
+;track_motorx 0
+
+# Set motorx reverse (default: 0)
+;track_motorx_reverse 0
# Motor number for y-axis (default: 0)
-track_motory 0
+;track_motory 1
+
+# Set motory reverse (default: 0)
+;track_motory_reverse 0
# Maximum value on x-axis (default: 0)
-track_maxx 0
+;track_maxx 200
+
+# Minimum value on x-axis (default: 0)
+;track_minx 50
# Maximum value on y-axis (default: 0)
-track_maxy 0
+;track_maxy 200
+
+# Minimum value on y-axis (default: 0)
+;track_miny 50
+
+# Center value on x-axis (default: 0)
+;track_homex 128
+
+# Center value on y-axis (default: 0)
+;track_homey 128
# ID of an iomojo camera if used (default: 0)
track_iomojo_id 0
@@ -492,7 +618,7 @@ track_stepsize 40
# You can use conversion specifiers for the on_xxxx commands
# %Y = year, %m = month, %d = date,
# %H = hour, %M = minute, %S = second,
-# %v = event, %q = frame number, %t = thread (camera) number,
+# %v = event, %q = frame number, %t = camera id number,
# %D = changed pixels, %N = noise level,
# %i and %J = width and height of motion area,
# %K and %L = X and Y coordinates of motion center
@@ -509,11 +635,11 @@ track_stepsize 40
quiet on
# Command to be executed when an event starts. (default: none)
-# An event starts at first motion detected after a period of no motion defined by gap
+# An event starts at first motion detected after a period of no motion defined by event_gap
; on_event_start value
# Command to be executed when an event ends after a period of no motion
-# (default: none). The period of no motion is defined by option gap.
+# (default: none). The period of no motion is defined by option event_gap.
; on_event_end value
# Command to be executed when a picture (.ppm|.jpg) is saved (default: none)
@@ -536,27 +662,27 @@ quiet on
; on_movie_end value
# Command to be executed when a camera can't be opened or if it is lost
-# NOTE: There is situations when motion doesn't detect a lost camera!
-# It depends on the driver, some drivers don't detect a lost camera at all
-# Some hang the motion thread. Some even hang the PC! (default: none)
+# NOTE: There is situations when motion don't detect a lost camera!
+# It depends on the driver, some drivers dosn't detect a lost camera at all
+# Some hangs the motion thread. Some even hangs the PC! (default: none)
; on_camera_lost value
-############################################################
-# Common Options For MySQL and PostgreSQL database features.
-# Options require the MySQL/PostgreSQL options to be active also.
-############################################################
+#####################################################################
+# Common Options for database features.
+# Options require database options to be active also.
+#####################################################################
-# Log to the database when creating motion triggered image file (default: on)
-sql_log_image on
+# Log to the database when creating motion triggered picture file (default: on)
+; sql_log_picture on
# Log to the database when creating a snapshot image file (default: on)
-sql_log_snapshot on
+; sql_log_snapshot on
-# Log to the database when creating motion triggered mpeg file (default: off)
-sql_log_mpeg off
+# Log to the database when creating motion triggered movie file (default: off)
+; sql_log_movie off
-# Log to the database when creating timelapse mpeg file (default: off)
-sql_log_timelapse off
+# Log to the database when creating timelapse movies file (default: off)
+; sql_log_timelapse off
# SQL query string that is sent to the database
# Use same conversion specifiers has for text features
@@ -564,45 +690,46 @@ sql_log_timelapse off
# %n = the number representing the file_type
# %f = filename with full path
# Default value:
+# Create tables :
+##
+# Mysql
+# CREATE TABLE security (camera int, filename char(80) not null, frame int, file_type int, time_stamp timestamp(14), event_time_stamp timestamp(14));
+#
+# Postgresql
+# CREATE TABLE security (camera int, filename char(80) not null, frame int, file_type int, time_stamp timestamp without time zone, event_time_stamp timestamp without time zone);
+#
# insert into security(camera, filename, frame, file_type, time_stamp, text_event) values('%t', '%f', '%q', '%n', '%Y-%m-%d %T', '%C')
-sql_query insert into security(camera, filename, frame, file_type, time_stamp, event_time_stamp) values('%t', '%f', '%q', '%n', '%Y-%m-%d %T', '%C')
+; sql_query insert into security(camera, filename, frame, file_type, time_stamp, event_time_stamp) values('%t', '%f', '%q', '%n', '%Y-%m-%d %T', '%C')
############################################################
-# Database Options For MySQL
+# Database Options
############################################################
-# Mysql database to log to (default: not defined)
-; mysql_db value
-
-# The host on which the database is located (default: localhost)
-; mysql_host value
-
-# User account name for MySQL database (default: not defined)
-; mysql_user value
+# database type : mysql, postgresql, sqlite3 (default : not defined)
+; database_type mysql
-# User password for MySQL database (default: not defined)
-; mysql_password value
+# database to log to (default: not defined)
+# for sqlite3, the full path and name for the database.
+; database_dbname motion
+# The host on which the database is located (default: localhost)
+; database_host 127.0.0.1
-############################################################
-# Database Options For PostgreSQL
-############################################################
-
-# PostgreSQL database to log to (default: not defined)
-; pgsql_db value
+# User account name for database (default: not defined)
+; database_user motion
-# The host on which the database is located (default: localhost)
-; pgsql_host value
+# User password for database (default: not defined)
+; database_password changeme
-# User account name for PostgreSQL database (default: not defined)
-; pgsql_user value
+# Port on which the database is located
+# mysql 3306 , postgresql 5432 (default: not defined)
+; database_port 3306
-# User password for PostgreSQL database (default: not defined)
-; pgsql_password value
+# Database wait time in milliseconds for locked database to
+# be unlocked before returning database locked error (default 0)
+; database_busy_timeout 0
-# Port on which the PostgreSQL database is located (default: 5432)
-; pgsql_port 5432
############################################################
@@ -619,19 +746,25 @@ sql_query insert into security(camera, filename, frame, file_type, time_stamp, e
##############################################################
-# Thread config files - One for each camera.
+# camera config files - One for each camera.
# Except if only one camera - You only need this config file.
-# If you have more than one camera you MUST define one thread
+# If you have more than one camera you MUST define one camera
# config file for each camera in addition to this config file.
##############################################################
# Remember: If you have more than one camera you must have one
-# thread file for each camera. E.g. 2 cameras requires 3 files:
-# This motion.conf file AND thread1.conf and thread2.conf.
+# camera file for each camera. E.g. 2 cameras requires 3 files:
+# This motion.conf file AND camera1.conf and camera2.conf.
# Only put the options that are unique to each camera in the
-# thread config files.
-; thread /usr/local/etc/thread1.conf
-; thread /usr/local/etc/thread2.conf
-; thread /usr/local/etc/thread3.conf
-; thread /usr/local/etc/thread4.conf
+# camera config files.
+; camera /etc/motion/camera1.conf
+; camera /etc/motion/camera2.conf
+; camera /etc/motion/camera3.conf
+; camera /etc/motion/camera4.conf
+
+##############################################################
+# Camera config directory - One for each camera.
+##############################################################
+#
+; camera_dir /etc/motion/conf.d
diff --git a/config/rootfiles/packages/motion b/config/rootfiles/packages/motion
index aa3e5b7..7905f8e 100644
--- a/config/rootfiles/packages/motion
+++ b/config/rootfiles/packages/motion
@@ -1,27 +1,29 @@
-#etc/motion-dist.conf
-etc/motion.conf
+etc/motion
+#etc/motion/camera1.conf
+#etc/motion/camera2.conf
+#etc/motion/camera3.conf
+#etc/motion/camera4.conf
+#etc/motion/motion.conf
usr/bin/motion
-#usr/share/doc/motion-3.2.12
-#usr/share/doc/motion-3.2.12/CHANGELOG
-#usr/share/doc/motion-3.2.12/COPYING
-#usr/share/doc/motion-3.2.12/CREDITS
-#usr/share/doc/motion-3.2.12/INSTALL
-#usr/share/doc/motion-3.2.12/README
-#usr/share/doc/motion-3.2.12/motion_guide.html
+#usr/share/doc/motion
+#usr/share/doc/motion/CHANGELOG
+#usr/share/doc/motion/COPYING
+#usr/share/doc/motion/CREDITS
+#usr/share/doc/motion/README.md
+#usr/share/doc/motion/mask1.png
+#usr/share/doc/motion/motion_guide.html
+#usr/share/doc/motion/normal.jpg
+#usr/share/doc/motion/outputmotion1.jpg
+#usr/share/doc/motion/outputnormal1.jpg
#usr/share/man/man1/motion.1
-#usr/share/motion-3.2.12
-#usr/share/motion-3.2.12/examples
-#usr/share/motion-3.2.12/examples/motion-dist.conf
-#usr/share/motion-3.2.12/examples/motion.init-Debian
-#usr/share/motion-3.2.12/examples/motion.init-Fedora
-#usr/share/motion-3.2.12/examples/motion.init-FreeBSD.sh
-#usr/share/motion-3.2.12/examples/motion.init-RH
-#usr/share/motion-3.2.12/examples/thread1.conf
-#usr/share/motion-3.2.12/examples/thread2.conf
-#usr/share/motion-3.2.12/examples/thread3.conf
-#usr/share/motion-3.2.12/examples/thread4.conf
+#usr/share/motion
+#usr/share/motion/examples
+#usr/share/motion/examples/camera1-dist.conf
+#usr/share/motion/examples/camera2-dist.conf
+#usr/share/motion/examples/camera3-dist.conf
+#usr/share/motion/examples/camera4-dist.conf
+#usr/share/motion/examples/motion-dist.conf
+#usr/share/motion/examples/motion.init-Debian
+#usr/share/motion/examples/motion.init-FreeBSD.sh
+#usr/share/motion/examples/motion.service
var/ipfire/backup/addons/includes/motion
-etc/rc.d/init.d/motion
-etc/rc.d/rc0.d/K01motion
-etc/rc.d/rc6.d/K01motion
-etc/rc.d/rc3.d/S99motion
diff --git a/lfs/motion b/lfs/motion
index 39c6b73..0e70c1e 100644
--- a/lfs/motion
+++ b/lfs/motion
@@ -1,7 +1,7 @@
###############################################################################
# #
# IPFire.org - A linux based firewall #
-# Copyright (C) 2007 Michael Tremer & Christian Schmidt #
+# Copyright (C) 2007-2016 IPFire Team <info(a)ipfire.org> #
# #
# This program is free software: you can redistribute it and/or modify #
# it under the terms of the GNU General Public License as published by #
@@ -24,16 +24,16 @@
include Config
-VER = 3.2.12
+VER = 4.0.1
-THISAPP = motion-$(VER)
+THISAPP = motion-release-$(VER)
DL_FILE = $(THISAPP).tar.gz
DL_FROM = $(URL_IPFIRE)
DIR_APP = $(DIR_SRC)/$(THISAPP)
TARGET = $(DIR_INFO)/$(THISAPP)
PROG = motion
-PAK_VER = 1
+PAK_VER = 2
DEPS = "ffmpeg"
###############################################################################
@@ -44,7 +44,7 @@ objects = $(DL_FILE)
$(DL_FILE) = $(DL_FROM)/$(DL_FILE)
-$(DL_FILE)_MD5 = 1ba0065ed50509aaffb171594c689f46
+$(DL_FILE)_MD5 = 5c87f90c4118d8cf0fb14700db69118f
install : $(TARGET)
@@ -76,20 +76,14 @@ dist:
$(TARGET) : $(patsubst %,$(DIR_DL)/%,$(objects))
@$(PREBUILD)
- @rm -rf $(DIR_APP) && cd $(DIR_SRC) && tar zxf $(DIR_DL)/$(DL_FILE)
-
- #Install obsolete V4L1 videodev.h
- cp $(DIR_SRC)/config/include/obsolete_videodev.h /usr/include/linux/videodev.h
-
- cd $(DIR_APP) && ./configure --prefix=/usr --sysconfdir=/etc
+ @rm -rf $(DIR_APP) && cd $(DIR_SRC) && tar axf $(DIR_DL)/$(DL_FILE)
+ cd $(DIR_APP) && autoreconf
+ cd $(DIR_APP) && ./configure --prefix=/usr --sysconfdir=/etc --with-ffmpeg
cd $(DIR_APP) && make $(MAKETUNING)
cd $(DIR_APP) && make install
- cp -vf $(DIR_SRC)/config/motion/motion.conf /etc
+ rm -vf /etc/motion/*.conf
+ cp -vf $(DIR_SRC)/config/motion/*.conf /etc/motion/
install -v -m 644 $(DIR_SRC)/config/backup/includes/motion \
/var/ipfire/backup/addons/includes/motion
-
- #Remove obsolete V4L1 videodev.h
- rm -f /usr/include/linux/videodev.h
-
@rm -rf $(DIR_APP)
@$(POSTBUILD)
--
2.9.3
^ permalink raw reply [flat|nested] 11+ messages in thread