http://git.ipfire.org/?p=ipfire-2.x.git;a=commitdiff;h=3d7e6b4b6146c85dfd0b5804242e0847f3645525

Could you please test the next nightly build that contains this change?

On Fri, 2016-04-29 at 09:50 +0200, g6094199(a)freenet.de wrote:
>         Hi Michael,
> 
> 
> 
> as i said all nics are shown, even in ip link:
> 
> 1: lo:  mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default 
>     link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
> 2: eth0:  mtu 1500 qdisc fq_codel master red0 state DOWN mode DEFAULT group
> default qlen 1000
>     link/ether 00:90:7f:41:2d:25 brd ff:ff:ff:ff:ff:ff
> 3: eth1:  mtu 1500 qdisc fq_codel master red0 state DOWN mode DEFAULT group
> default qlen 1000
>     link/ether 00:90:7f:41:2d:24 brd ff:ff:ff:ff:ff:ff
> 4: eth2:  mtu 1500 qdisc fq_codel master red0 state DOWN mode DEFAULT group
> default qlen 1000
>     link/ether 00:90:7f:41:2d:23 brd ff:ff:ff:ff:ff:ff
> 5: green0: 
>  mtu 1500 qdisc fq_codel state UP mode DEFAULT group default qlen 1000
>     link/ether 00:90:7f:41:2d:22 brd ff:ff:ff:ff:ff:ff
> 6: eth4: 
>  mtu 1500 qdisc fq_codel master red0 state UP mode DEFAULT group default qlen
> 1000
>     link/ether 00:90:7f:41:2d:21 brd ff:ff:ff:ff:ff:ff
> 7: eth5:  mtu 1500 qdisc fq_codel master red0 state DOWN mode DEFAULT group
> default qlen 1000
>     link/ether 00:90:7f:41:2d:20 brd ff:ff:ff:ff:ff:ff
> 8: eth6:  mtu 1500 qdisc fq_codel master red0 state DOWN mode DEFAULT group
> default qlen 1000
>     link/ether 00:90:7f:41:2d:1f brd ff:ff:ff:ff:ff:ff
> 9: eth3:  mtu 1500 qdisc fq_codel master red0 state DOWN mode DEFAULT group
> default qlen 1000
>     link/ether 00:90:7f:41:2d:1e brd ff:ff:ff:ff:ff:ff
> 10: red0: 
>  mtu 1500 qdisc fq_codel state UP mode DEFAULT group default 
>     link/ether 00:90:7f:41:2d:1e brd ff:ff:ff:ff:ff:ff
> 
> 
> There ist no scroll bar in the setup. Also if you try to scroll down nothing
> happens.
> setup.log is empty
> 
> Since i'm running Core 100 (fresh embedded install), the limitation doesnt
> seem to be fixed.
> 
> I'm attaching an setup screenshot to your private mail.
> 
> 
> 
> regards 
> sash
> 
> 
> 
> 
> > 
> > -----Ursprüngliche Nachricht-----
> > Von: Michael Tremer 
> > Gesendet: Do. 28.04.2016 19:25
> > An: g6094199(a)freenet.de,  development(a)lists.ipfire.org
> > Betreff: Re: Possible configuration bug with >6 nics
> > 
> > Hello,
> > 
> > there was a limit prior to Core Update 100 but this should have gone away
> > and
> > actually 20 NICs should be shown by now.
> > 
> > Did you try to scroll down? Are there any errors shown?
> > 
> > What is the output of "ip link"?
> > 
> > Best,
> > -Michael
> > 
> > On Thu, 2016-04-28 at 16:52 +0200, g6094199(a)freenet.de wrote:
> > > 
> > > He guys!
> > >  
> > > i recently installed IPFire core 100 to an Watchguard Firebox X
> > > 750e/1000e.
> > > All installed to an CF-card, booted up fine.
> > > Came to the general setup and asked to map the nics to an interface. While
> > > the
> > > x750 has 8 nics (4x Marvell 88E8001, 4x 88E8053) only 6 nics are shown in
> > > the
> > > setup menue via serial port. which seems to be a limitation by the GUI or
> > > a
> > > bug.
> > >  
> > > I can see als of the interfaces on cli after i finished the initial setup
> > >  
> > > lspci:
> > > 01:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8053 PCI-E
> > > Gigabit Ethernet Controller (rev 19)
> > > 02:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8053 PCI-E
> > > Gigabit Ethernet Controller (rev 19)
> > > 03:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8053 PCI-E
> > > Gigabit Ethernet Controller (rev 19)
> > > 04:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8053 PCI-E
> > > Gigabit Ethernet Controller (rev 19)
> > > 05:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8001 Gigabit
> > > Ethernet Controller (rev 13)
> > > 05:01.0 Ethernet controller: Marvell Technology Group Ltd. 88E8001 Gigabit
> > > Ethernet Controller (rev 13)
> > > 05:02.0 Ethernet controller: Marvell Technology Group Ltd. 88E8001 Gigabit
> > > Ethernet Controller (rev 13)
> > > 05:03.0 Ethernet controller: Marvell Technology Group Ltd. 88E8001 Gigabit
> > > Ethernet Controller (rev 13)
> > >  
> > > I also can use them. So it seems to be a limitation/bug of the setup
> > > menue?!
> > >  
> > > Any thoughs?
> > >  
> > >  
> > > regards
> > > sash
> > > 
> > > 
> > > ---
> > > Mail & Cloud Made in Germany mit 3 GB Speicher! Jetzt kostenlos anmelden>
> > -----Ursprüngliche Nachricht Ende----
> 
>  
> 
> ---
> Alle Postfächer an einem Ort. Jetzt wechseln und E-Mail-Adresse mitnehmen! htt
> ps://email.freenet.de/mail/Uebersicht?epid=e9900000451
> 
>