Cool!

Thanks for the feedback. This fix will probably be included in Core Update 103
then.

Best,
-Michael

On Mon, 2016-05-02 at 12:38 +0200, g6094199(a)freenet.de wrote:
> Hi Michael!
> 
> 
> Just tested the current nightly. Now all 8 NICs are shown, so
> 
> bug -> fixed
> 
> 
> At least for 8 NIC devices :-)
> 
> 
> THX!
> 
> sash
> 
> 
> > 
> > -----Ursprüngliche Nachricht-----
> > Von: Michael Tremer 
> > Gesendet: Fr. 29.04.2016 14:24
> > An: g6094199(a)freenet.de,  development(a)lists.ipfire.org
> > Betreff: Re: Re: Possible configuration bug with >6 nics
> > 
> > http://git.ipfire.org/?p=ipfire-2.x.git;a=commitdiff;h=3d7e6b4b6146c85dfd0b5
> > 804242e0847f3645525
> > 
> > Could you please test the next nightly build that contains this change?
> > 
> > On Fri, 2016-04-29 at 09:50 +0200, g6094199(a)freenet.de wrote:
> > > 
> > >         Hi Michael,
> > > 
> > > 
> > > 
> > > as i said all nics are shown, even in ip link:
> > > 
> > > 1: lo:  mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default 
> > >     link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
> > > 2: eth0:  mtu 1500 qdisc fq_codel master red0 state DOWN mode DEFAULT
> > > group
> > > default qlen 1000
> > >     link/ether 00:90:7f:41:2d:25 brd ff:ff:ff:ff:ff:ff
> > > 3: eth1:  mtu 1500 qdisc fq_codel master red0 state DOWN mode DEFAULT
> > > group
> > > default qlen 1000
> > >     link/ether 00:90:7f:41:2d:24 brd ff:ff:ff:ff:ff:ff
> > > 4: eth2:  mtu 1500 qdisc fq_codel master red0 state DOWN mode DEFAULT
> > > group
> > > default qlen 1000
> > >     link/ether 00:90:7f:41:2d:23 brd ff:ff:ff:ff:ff:ff
> > > 5: green0: 
> > >  mtu 1500 qdisc fq_codel state UP mode DEFAULT group default qlen 1000
> > >     link/ether 00:90:7f:41:2d:22 brd ff:ff:ff:ff:ff:ff
> > > 6: eth4: 
> > >  mtu 1500 qdisc fq_codel master red0 state UP mode DEFAULT group default
> > > qlen
> > > 1000
> > >     link/ether 00:90:7f:41:2d:21 brd ff:ff:ff:ff:ff:ff
> > > 7: eth5:  mtu 1500 qdisc fq_codel master red0 state DOWN mode DEFAULT
> > > group
> > > default qlen 1000
> > >     link/ether 00:90:7f:41:2d:20 brd ff:ff:ff:ff:ff:ff
> > > 8: eth6:  mtu 1500 qdisc fq_codel master red0 state DOWN mode DEFAULT
> > > group
> > > default qlen 1000
> > >     link/ether 00:90:7f:41:2d:1f brd ff:ff:ff:ff:ff:ff
> > > 9: eth3:  mtu 1500 qdisc fq_codel master red0 state DOWN mode DEFAULT
> > > group
> > > default qlen 1000
> > >     link/ether 00:90:7f:41:2d:1e brd ff:ff:ff:ff:ff:ff
> > > 10: red0: 
> > >  mtu 1500 qdisc fq_codel state UP mode DEFAULT group default 
> > >     link/ether 00:90:7f:41:2d:1e brd ff:ff:ff:ff:ff:ff
> > > 
> > > 
> > > There ist no scroll bar in the setup. Also if you try to scroll down
> > > nothing
> > > happens.
> > > setup.log is empty
> > > 
> > > Since i'm running Core 100 (fresh embedded install), the limitation doesnt
> > > seem to be fixed.
> > > 
> > > I'm attaching an setup screenshot to your private mail.
> > > 
> > > 
> > > 
> > > regards 
> > > sash
> > > 
> > > 
> > > 
> > > 
> > > > 
> > > > 
> > > > -----Ursprüngliche Nachricht-----
> > > > Von: Michael Tremer 
> > > > Gesendet: Do. 28.04.2016 19:25
> > > > An: g6094199(a)freenet.de,  development(a)lists.ipfire.org
> > > > Betreff: Re: Possible configuration bug with >6 nics
> > > > 
> > > > Hello,
> > > > 
> > > > there was a limit prior to Core Update 100 but this should have gone
> > > > away
> > > > and
> > > > actually 20 NICs should be shown by now.
> > > > 
> > > > Did you try to scroll down? Are there any errors shown?
> > > > 
> > > > What is the output of "ip link"?
> > > > 
> > > > Best,
> > > > -Michael
> > > > 
> > > > On Thu, 2016-04-28 at 16:52 +0200, g6094199(a)freenet.de wrote:
> > > > > 
> > > > > 
> > > > > He guys!
> > > > >  
> > > > > i recently installed IPFire core 100 to an Watchguard Firebox X
> > > > > 750e/1000e.
> > > > > All installed to an CF-card, booted up fine.
> > > > > Came to the general setup and asked to map the nics to an interface.
> > > > > While
> > > > > the
> > > > > x750 has 8 nics (4x Marvell 88E8001, 4x 88E8053) only 6 nics are shown
> > > > > in
> > > > > the
> > > > > setup menue via serial port. which seems to be a limitation by the GUI
> > > > > or
> > > > > a
> > > > > bug.
> > > > >  
> > > > > I can see als of the interfaces on cli after i finished the initial
> > > > > setup
> > > > >  
> > > > > lspci:
> > > > > 01:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8053
> > > > > PCI-E
> > > > > Gigabit Ethernet Controller (rev 19)
> > > > > 02:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8053
> > > > > PCI-E
> > > > > Gigabit Ethernet Controller (rev 19)
> > > > > 03:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8053
> > > > > PCI-E
> > > > > Gigabit Ethernet Controller (rev 19)
> > > > > 04:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8053
> > > > > PCI-E
> > > > > Gigabit Ethernet Controller (rev 19)
> > > > > 05:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8001
> > > > > Gigabit
> > > > > Ethernet Controller (rev 13)
> > > > > 05:01.0 Ethernet controller: Marvell Technology Group Ltd. 88E8001
> > > > > Gigabit
> > > > > Ethernet Controller (rev 13)
> > > > > 05:02.0 Ethernet controller: Marvell Technology Group Ltd. 88E8001
> > > > > Gigabit
> > > > > Ethernet Controller (rev 13)
> > > > > 05:03.0 Ethernet controller: Marvell Technology Group Ltd. 88E8001
> > > > > Gigabit
> > > > > Ethernet Controller (rev 13)
> > > > >  
> > > > > I also can use them. So it seems to be a limitation/bug of the setup
> > > > > menue?!
> > > > >  
> > > > > Any thoughs?
> > > > >  
> > > > >  
> > > > > regards
> > > > > sash
> > > > > 
> > > > > 
> > > > > ---
> > > > > Mail & Cloud Made in Germany mit 3 GB Speicher! Jetzt kostenlos
> > > > > anmelden>
> > > > -----Ursprüngliche Nachricht Ende----
> > >  
> > > 
> > > ---
> > > Alle Postfächer an einem Ort. Jetzt wechseln und E-Mail-Adresse mitnehmen!
> > > htt
> > > ps://email.freenet.de/mail/Uebersicht?epid=e9900000451
> > > 
> > > > 
> > > > 
> > -----Ursprüngliche Nachricht Ende-----
> 
>  
> 
> ---
> Alle Postfächer an einem Ort. Jetzt wechseln und E-Mail-Adresse mitnehmen! htt
> ps://email.freenet.de/mail/Uebersicht?epid=e9900000451
> 
>