Thanks.  That was my original conversation! :-)  I will just wait for 
Arne to find some time.

On 6/10/24 11:42 AM, Michael Tremer wrote:
> Hello Craig,
>
> Hmm, I am not the right person to talk to about this, but it looks this has all been discussed here already:
>
>    https://community.ipfire.org/t/hang-with-kernel-starting-on-raspberry-pi/11558
>
> -Michael
>
>> On 4 Jun 2024, at 13:40, Craig Setera <craigjunk(a)setera.org> wrote:
>>
>> Thanks Michael,
>>
>> Is there anything more you need me to do?  I assume most of the current effort is currently focused on the test release.
>>
>> Thanks,
>> Craig
>>
>> On 5/23/24 12:01 PM, Michael Tremer wrote:
>>> Hello Craig,
>>>
>>> Thank you very much for this patch. This is perfectly readable :)
>>>
>>> It looks logical to me, however I am not an expert when it comes to SBCs, so I will leave this for Arne to review and merge.
>>>
>>> Best,
>>> -Michael
>>>
>>>> On 20 May 2024, at 13:17, Craig Setera <craigjunk(a)setera.org> wrote:
>>>>
>>>> Updates to u-boot script for Raspberry Pi 4b devices to
>>>> properly configure the serial console and to choose the proper boot address
>>>> to be used on newer board revisions.  With these changes in place, I'm able
>>>> to fully boot into a serial console in u-boot.
>>>>
>>>> The serial console configuration was derived from the Grub configuration,
>>>> while the boot address changes were taken from the IPFire Raspberry 4b
>>>> documentation page: https://www.ipfire.org/docs/hardware/arm/rpi/four
>>>>
>>>> Per the conversation in the forums, I don't know why the boot
>>>> address changes are required.  I was simply trying to automate those
>>>> changes such that downloaded builds will work out of the box.
>>>> https://community.ipfire.org/t/hang-with-kernel-starting-on-raspberry-pi/11558/37
>>>>
>>>> NOTE: The use of the different parameter options to the test
>>>> command to minimize the need for deeply nested conditionals.  I did
>>>> try more bash-shell like syntax, but u-boot didn't seem to like that.
>>>> The operators used here were found in the u-boot source.
>>>>
>>>> Tested-by: Craig Setera <craigjunk(a)setera.org>
>>>> Signed-off-by: Craig Setera <craigjunk(a)setera.org>
>>>> ---
>>>>   config/u-boot/boot.cmd | 27 ++++++++++++++++++++++++---
>>>>   1 file changed, 24 insertions(+), 3 deletions(-)
>>>>
>>>> diff --git a/config/u-boot/boot.cmd b/config/u-boot/boot.cmd
>>>> index a27996780..eedd5776d 100644
>>>> --- a/config/u-boot/boot.cmd
>>>> +++ b/config/u-boot/boot.cmd
>>>> @@ -51,7 +51,11 @@ if test "${SERIAL-CONSOLE}" = "ON"; then
>>>>                       if test "${fdtfile}" = "broadcom/bcm2837-rpi-3-b.dtb"; then
>>>>                           setenv console ttyS1,115200n8;
>>>>                       else
>>>> -                        setenv console ttyAMA0,115200n8;
>>>> +                        if test "${fdtfile}" = "broadcom/bcm2711-rpi-4-b.dtb"; then
>>>> +                            setenv console ttyS0,115200n8;
>>>> +                        else
>>>> +                            setenv console ttyAMA0,115200n8;
>>>> +                        fi;
>>>>                       fi;
>>>>                   fi;
>>>>               else
>>>> @@ -95,11 +99,28 @@ else
>>>>       setenv ramdisk_addr -;
>>>>   fi;
>>>>
>>>> +#
>>>> +# Handle Raspberry Pi 4 address differences
>>>> +# https://www.ipfire.org/docs/hardware/arm/rpi/four
>>>> +#
>>>> +setenv booti_fdt_addr ${fdt_addr_r};
>>>> +if test "${board}" -eq "rpi" -a ${cpu} -eq "armv8" -a "${fdtfile}" -eq "broadcom/bcm2711-rpi-4-b.dtb"; then
>>>> +    # Hardware revision 1.4
>>>> +    if test ${board_revision} -eq 0xB03114 -o ${board_revision} -eq 0xC03114 -o ${board_revision} -eq 0xD03114; then
>>>> +        setenv booti_fdt_addr ${fdt_addr};
>>>> +    fi
>>>> +
>>>> +    # Hardware revision 1.5
>>>> +    if test ${board_revision} -eq 0xB03115 -o ${board_revision} -eq 0xC03115 -o ${board_revision} -eq 0xD03115; then
>>>> +        setenv booti_fdt_addr ${fdt_addr};
>>>> +    fi
>>>> +fi;
>>>> +
>>>>   bootz ${kernel_addr_r} ${ramdisk_addr} ${fdt_addr_r};
>>>> -booti ${kernel_addr_r} ${ramdisk_addr} ${fdt_addr_r};
>>>> +booti ${kernel_addr_r} ${ramdisk_addr} ${booti_fdt_addr};
>>>>
>>>>   bootz ${kernel_addr_r} - ${fdt_addr_r};
>>>> -booti ${kernel_addr_r} - ${fdt_addr_r};
>>>> +booti ${kernel_addr_r} - ${booti_fdt_addr};
>>>>
>>>>   # Recompile with:
>>>>   # mkimage -C none -A arm -T script -d /boot/boot.cmd /boot/boot.scr
>>>> -- 
>>>> 2.40.1
>>>>
>>>>