Hello Craig,

Hmm, I am not the right person to talk to about this, but it looks this has all been discussed here already:

  https://community.ipfire.org/t/hang-with-kernel-starting-on-raspberry-pi/11558

-Michael

> On 4 Jun 2024, at 13:40, Craig Setera <craigjunk(a)setera.org> wrote:
> 
> Thanks Michael,
> 
> Is there anything more you need me to do?  I assume most of the current effort is currently focused on the test release.
> 
> Thanks,
> Craig
> 
> On 5/23/24 12:01 PM, Michael Tremer wrote:
>> Hello Craig,
>> 
>> Thank you very much for this patch. This is perfectly readable :)
>> 
>> It looks logical to me, however I am not an expert when it comes to SBCs, so I will leave this for Arne to review and merge.
>> 
>> Best,
>> -Michael
>> 
>>> On 20 May 2024, at 13:17, Craig Setera <craigjunk(a)setera.org> wrote:
>>> 
>>> Updates to u-boot script for Raspberry Pi 4b devices to
>>> properly configure the serial console and to choose the proper boot address
>>> to be used on newer board revisions.  With these changes in place, I'm able
>>> to fully boot into a serial console in u-boot.
>>> 
>>> The serial console configuration was derived from the Grub configuration,
>>> while the boot address changes were taken from the IPFire Raspberry 4b
>>> documentation page: https://www.ipfire.org/docs/hardware/arm/rpi/four
>>> 
>>> Per the conversation in the forums, I don't know why the boot
>>> address changes are required.  I was simply trying to automate those
>>> changes such that downloaded builds will work out of the box.
>>> https://community.ipfire.org/t/hang-with-kernel-starting-on-raspberry-pi/11558/37
>>> 
>>> NOTE: The use of the different parameter options to the test
>>> command to minimize the need for deeply nested conditionals.  I did
>>> try more bash-shell like syntax, but u-boot didn't seem to like that.
>>> The operators used here were found in the u-boot source.
>>> 
>>> Tested-by: Craig Setera <craigjunk(a)setera.org>
>>> Signed-off-by: Craig Setera <craigjunk(a)setera.org>
>>> ---
>>>  config/u-boot/boot.cmd | 27 ++++++++++++++++++++++++---
>>>  1 file changed, 24 insertions(+), 3 deletions(-)
>>> 
>>> diff --git a/config/u-boot/boot.cmd b/config/u-boot/boot.cmd
>>> index a27996780..eedd5776d 100644
>>> --- a/config/u-boot/boot.cmd
>>> +++ b/config/u-boot/boot.cmd
>>> @@ -51,7 +51,11 @@ if test "${SERIAL-CONSOLE}" = "ON"; then
>>>                      if test "${fdtfile}" = "broadcom/bcm2837-rpi-3-b.dtb"; then
>>>                          setenv console ttyS1,115200n8;
>>>                      else
>>> -                        setenv console ttyAMA0,115200n8;
>>> +                        if test "${fdtfile}" = "broadcom/bcm2711-rpi-4-b.dtb"; then
>>> +                            setenv console ttyS0,115200n8;
>>> +                        else
>>> +                            setenv console ttyAMA0,115200n8;
>>> +                        fi;
>>>                      fi;
>>>                  fi;
>>>              else
>>> @@ -95,11 +99,28 @@ else
>>>      setenv ramdisk_addr -;
>>>  fi;
>>> 
>>> +#
>>> +# Handle Raspberry Pi 4 address differences
>>> +# https://www.ipfire.org/docs/hardware/arm/rpi/four
>>> +#
>>> +setenv booti_fdt_addr ${fdt_addr_r};
>>> +if test "${board}" -eq "rpi" -a ${cpu} -eq "armv8" -a "${fdtfile}" -eq "broadcom/bcm2711-rpi-4-b.dtb"; then
>>> +    # Hardware revision 1.4
>>> +    if test ${board_revision} -eq 0xB03114 -o ${board_revision} -eq 0xC03114 -o ${board_revision} -eq 0xD03114; then
>>> +        setenv booti_fdt_addr ${fdt_addr};
>>> +    fi
>>> +
>>> +    # Hardware revision 1.5
>>> +    if test ${board_revision} -eq 0xB03115 -o ${board_revision} -eq 0xC03115 -o ${board_revision} -eq 0xD03115; then
>>> +        setenv booti_fdt_addr ${fdt_addr};
>>> +    fi
>>> +fi;
>>> +
>>>  bootz ${kernel_addr_r} ${ramdisk_addr} ${fdt_addr_r};
>>> -booti ${kernel_addr_r} ${ramdisk_addr} ${fdt_addr_r};
>>> +booti ${kernel_addr_r} ${ramdisk_addr} ${booti_fdt_addr};
>>> 
>>>  bootz ${kernel_addr_r} - ${fdt_addr_r};
>>> -booti ${kernel_addr_r} - ${fdt_addr_r};
>>> +booti ${kernel_addr_r} - ${booti_fdt_addr};
>>> 
>>>  # Recompile with:
>>>  # mkimage -C none -A arm -T script -d /boot/boot.cmd /boot/boot.scr
>>> -- 
>>> 2.40.1
>>> 
>>>