From mboxrd@z Thu Jan 1 00:00:00 1970 From: g6094199@freenet.de To: development@lists.ipfire.org Subject: RE: Re: Re: Possible configuration bug with >6 nics Date: Mon, 02 May 2016 12:38:49 +0200 Message-ID: MIME-Version: 1.0 Content-Type: multipart/mixed; boundary="===============1496179609304076995==" List-Id: --===============1496179609304076995== Content-Type: text/plain; charset="utf-8" Content-Transfer-Encoding: quoted-printable Hi Michael! Just tested the current nightly. Now all 8 NICs are shown, so bug -> fixed At least for 8 NIC devices :-) THX! sash > -----Urspr=C3=BCngliche Nachricht----- > Von: Michael Tremer=20 > Gesendet: Fr. 29.04.2016 14:24 > An: g6094199(a)freenet.de, development(a)lists.ipfire.org > Betreff: Re: Re: Possible configuration bug with >6 nics > >http://git.ipfire.org/?p=3Dipfire-2.x.git;a=3Dcommitdiff;h=3D3d7e6b4b6146c85= dfd0b5804242e0847f3645525 > > Could you please test the next nightly build that contains this change? > > On Fri, 2016-04-29 at 09:50 +0200, g6094199(a)freenet.de wrote: >> Hi Michael, >> >> >> >> as i said all nics are shown, even in ip link: >> >> 1: lo: mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default=20 >> link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 >> 2: eth0: mtu 1500 qdisc fq_codel master red0 state DOWN mode DEFAULT group >> default qlen 1000 >> link/ether 00:90:7f:41:2d:25 brd ff:ff:ff:ff:ff:ff >> 3: eth1: mtu 1500 qdisc fq_codel master red0 state DOWN mode DEFAULT group >> default qlen 1000 >> link/ether 00:90:7f:41:2d:24 brd ff:ff:ff:ff:ff:ff >> 4: eth2: mtu 1500 qdisc fq_codel master red0 state DOWN mode DEFAULT group >> default qlen 1000 >> link/ether 00:90:7f:41:2d:23 brd ff:ff:ff:ff:ff:ff >> 5: green0:=20 >> mtu 1500 qdisc fq_codel state UP mode DEFAULT group default qlen 1000 >> link/ether 00:90:7f:41:2d:22 brd ff:ff:ff:ff:ff:ff >> 6: eth4:=20 >> mtu 1500 qdisc fq_codel master red0 state UP mode DEFAULT group default q= len >> 1000 >> link/ether 00:90:7f:41:2d:21 brd ff:ff:ff:ff:ff:ff >> 7: eth5: mtu 1500 qdisc fq_codel master red0 state DOWN mode DEFAULT group >> default qlen 1000 >> link/ether 00:90:7f:41:2d:20 brd ff:ff:ff:ff:ff:ff >> 8: eth6: mtu 1500 qdisc fq_codel master red0 state DOWN mode DEFAULT group >> default qlen 1000 >> link/ether 00:90:7f:41:2d:1f brd ff:ff:ff:ff:ff:ff >> 9: eth3: mtu 1500 qdisc fq_codel master red0 state DOWN mode DEFAULT group >> default qlen 1000 >> link/ether 00:90:7f:41:2d:1e brd ff:ff:ff:ff:ff:ff >> 10: red0:=20 >> mtu 1500 qdisc fq_codel state UP mode DEFAULT group default=20 >> link/ether 00:90:7f:41:2d:1e brd ff:ff:ff:ff:ff:ff >> >> >> There ist no scroll bar in the setup. Also if you try to scroll down nothi= ng >> happens. >> setup.log is empty >> >> Since i'm running Core 100 (fresh embedded install), the limitation doesnt >> seem to be fixed. >> >> I'm attaching an setup screenshot to your private mail. >> >> >> >> regards=20 >> sash >> >> >> >> >> > >> > -----Urspr=C3=BCngliche Nachricht----- >> > Von: Michael Tremer=20 >> > Gesendet: Do. 28.04.2016 19:25 >> > An: g6094199(a)freenet.de, development(a)lists.ipfire.org >> > Betreff: Re: Possible configuration bug with >6 nics >> > >> > Hello, >> > >> > there was a limit prior to Core Update 100 but this should have gone away >> > and >> > actually 20 NICs should be shown by now. >> > >> > Did you try to scroll down? Are there any errors shown? >> > >> > What is the output of "ip link"? >> > >> > Best, >> > -Michael >> > >> > On Thu, 2016-04-28 at 16:52 +0200, g6094199(a)freenet.de wrote: >> > > >> > > He guys! >> > > =20 >> > > i recently installed IPFire core 100 to an Watchguard Firebox X >> > > 750e/1000e. >> > > All installed to an CF-card, booted up fine. >> > > Came to the general setup and asked to map the nics to an interface. W= hile >> > > the >> > > x750 has 8 nics (4x Marvell 88E8001, 4x 88E8053) only 6 nics are shown= in >> > > the >> > > setup menue via serial port. which seems to be a limitation by the GUI= or >> > > a >> > > bug. >> > > =20 >> > > I can see als of the interfaces on cli after i finished the initial se= tup >> > > =20 >> > > lspci: >> > > 01:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8053 PCI= -E >> > > Gigabit Ethernet Controller (rev 19) >> > > 02:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8053 PCI= -E >> > > Gigabit Ethernet Controller (rev 19) >> > > 03:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8053 PCI= -E >> > > Gigabit Ethernet Controller (rev 19) >> > > 04:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8053 PCI= -E >> > > Gigabit Ethernet Controller (rev 19) >> > > 05:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8001 Gig= abit >> > > Ethernet Controller (rev 13) >> > > 05:01.0 Ethernet controller: Marvell Technology Group Ltd. 88E8001 Gig= abit >> > > Ethernet Controller (rev 13) >> > > 05:02.0 Ethernet controller: Marvell Technology Group Ltd. 88E8001 Gig= abit >> > > Ethernet Controller (rev 13) >> > > 05:03.0 Ethernet controller: Marvell Technology Group Ltd. 88E8001 Gig= abit >> > > Ethernet Controller (rev 13) >> > > =20 >> > > I also can use them. So it seems to be a limitation/bug of the setup >> > > menue?! >> > > =20 >> > > Any thoughs? >> > > =20 >> > > =20 >> > > regards >> > > sash >> > > >> > > >> > > --- >> > > Mail & Cloud Made in Germany mit 3 GB Speicher! Jetzt kostenlos anmeld= en> >> > -----Urspr=C3=BCngliche Nachricht Ende---- >> >> =20 >> >> --- >> Alle Postf=C3=A4cher an einem Ort. Jetzt wechseln und E-Mail-Adresse mitne= hmen! htt >> ps://email.freenet.de/mail/Uebersicht?epid=3De9900000451 >> >>> > > -----Urspr=C3=BCngliche Nachricht Ende----- =20 --- Alle Postf=C3=A4cher an einem Ort. Jetzt wechseln und E-Mail-Adresse mitnehme= n! https://email.freenet.de/mail/Uebersicht?epid=3De9900000451 --===============1496179609304076995==--