Hello,

thanks for sending in this patch.

I consider this slightly messy since the solution to the problem is not a very
good one. But we don't have anything better either. So I hope we will be able at
some time to come back to this and improve it a little bit.

-Michael

On Thu, 2018-03-01 at 15:15 +0000, Jonatan Schlag wrote:
> Based on the examples found in strongswan
> we need to specific the source IP for our routes through an IPsec VPN.
> If we have no source IP (a router can route packages
> which do not belong to the network assigned to our zones) we set no routes,
> but clients can still use the tunnel.
> 
> For IPsec VPNs in tunnel mode we
> also need the device which has the ${PLUTO_ME} IP address asigned.
> 
> The source IP  is determined ip_get_assigned_addresses_from_net()
> the device is determined by the  device_get_by_ip_address() function.
> 
> For tunnel mode see:
> https://www.strongswan.org/testing/testresults/ipv6-stroke/net2net-ip4-in-ip6-
> ikev2/moon.ip.route
> 
> Fixes: #11629
> 
> Signed-off-by: Jonatan Schlag <jonatan.schlag(a)ipfire.org>
> ---
>  src/helpers/ipsec-updown | 46 +++++++++++++++++++++++++++++++++++++++-------
>  1 file changed, 39 insertions(+), 7 deletions(-)
> 
> diff --git a/src/helpers/ipsec-updown b/src/helpers/ipsec-updown
> index 12ead03..3764085 100644
> --- a/src/helpers/ipsec-updown
> +++ b/src/helpers/ipsec-updown
> @@ -86,13 +86,45 @@ case "${PLUTO_VERB}" in
>  				;;
>  		esac
>  
> -		# Set routes
> -		if isset INTERFACE; then
> -			cmd ip route add "${PLUTO_PEER_CLIENT}" \
> -				dev "${INTERFACE}"
> -		else
> -			cmd ip route add "${PLUTO_PEER_CLIENT}" \
> -				via "${PLUTO_PEER}"
> +		#Get sources IP for routes
> +		SRC_IP=($(ip_get_assigned_addresses_from_net \
> +			"${PLUTO_MY_CLIENT}" "permanent"))
> +
> +		# Set routes if we have a source IP.
> +		# If not the machine does not has a leg on the net
> +		# and we can go on without routes.
> +		if isset SRC_IP; then
> +			# We take the lowest source IP we found,
> +			# which is ugly because the value is unpredictable.
> +			SRC_IP=${SRC_IP[0]}
> +
> +			if isset INTERFACE; then
> +				if ! cmd ip route add \
> +					"${PLUTO_PEER_CLIENT}" \
> +					dev "${INTERFACE}" \
> +					src "${SRC_IP}"; then
> +						log ERROR \
> +							"Could not set routes
> for ${PLUTO_PEER_CLIENT}"
> +				fi
> +			else
> +				# Get the device which we use to peer with
> the other site.
> +				ME_DEVICE = "$(device_get_by_ip_address
> "${PLUTO_ME}")"
> +
> +				# We can only go on if we found a device.
> +				if isset ME_DEVICE; then
> +					if ! cmd ip route add \
> +						"${PLUTO_PEER_CLIENT}" \
> +						dev "${ME_DEVICE}" \
> +						proto static \
> +						src "${SRC_IP}" \
> +						table 220; then
> +							log ERROR \
> +								"Could not
> set routes for ${PLUTO_PEER_CLIENT}"
> +					fi
> +				else
> +					log ERROR "Could not get device for
> ${PLUTO_ME}"
> +				fi
> +			fi
>  		fi
>  		;;
>