Re: jp1082 USB to Ethernet

Re: jp1082 USB to Ethernet

[Michael Tremer]

[-- Attachment #1: Type: text/plain, Size: 1704 bytes --]

No, there is no cross-compiler available.

On Mon, 2014-08-11 at 11:19 +0100, John Leake wrote:
> Hi Michael,
> Thank you for your reply.  Surely there is a cross compiler to run on x686 ?
> John
> On 11/08/14 10:31, Michael Tremer wrote:
> > Hey,
> >
> > you would either need an ARM build machine and do just the same like you
> > did on x86. However, building IPFire will take a while. Days instead of
> > hours.
> >
> > If you don't have a powerful ARM machine (the Raspberry Pi is not an
> > option at all) you can emulate one on x86. This is even slower even on
> > powerful x86 machines, but it works.
> >
> > I recommend Debian for that as it comes with a statically linked version
> > of qemu for ARM. Commands are much like when doing a native build, you
> > will just need to add the target architecture like this:
> >
> > ./make.sh clean
> > ./make.sh --target=armv5tel gettoolchain
> > ./make.sh --target=armv5tel downloadsrc
> > ./make.sh --target=armv5tel build
> >
> > Good luck!
> >
> > -Michael
> >
> > On Thu, 2014-07-31 at 00:34 +0100, John Leake wrote:
> >> Hi All,
> >> I have installed ipfire on my pi and all is ok except the very low cost
> >> jp1082 USB to Ethernet adapters are not recognised.
> >>
> >> I would like to build the jp drivers and include them in a pi ipfire SD
> >> image.
> >>
> >> I have forked the ipfire-2.x repo and successfully built the default
> >> image as a test (it took 3 hour(s) 52 minute(s) 55 second(s))!
> >>
> >> Can anyone tell me how to build the pi image ?
> >>
> >> Ozpoz
> >> _______________________________________________
> >> SIG-ARM mailing list
> >> SIG-ARM(a)lists.ipfire.org
> >> http://lists.ipfire.org/mailman/listinfo/sig-arm
> 

Re: jp1082 USB to Ethernet

[Michael Tremer]

[-- Attachment #1: Type: text/plain, Size: 1326 bytes --]

Hey,

you would either need an ARM build machine and do just the same like you
did on x86. However, building IPFire will take a while. Days instead of
hours.

If you don't have a powerful ARM machine (the Raspberry Pi is not an
option at all) you can emulate one on x86. This is even slower even on
powerful x86 machines, but it works.

I recommend Debian for that as it comes with a statically linked version
of qemu for ARM. Commands are much like when doing a native build, you
will just need to add the target architecture like this:

./make.sh clean
./make.sh --target=armv5tel gettoolchain
./make.sh --target=armv5tel downloadsrc
./make.sh --target=armv5tel build

Good luck!

-Michael

On Thu, 2014-07-31 at 00:34 +0100, John Leake wrote:
> Hi All,
> I have installed ipfire on my pi and all is ok except the very low cost
> jp1082 USB to Ethernet adapters are not recognised.
> 
> I would like to build the jp drivers and include them in a pi ipfire SD
> image.
> 
> I have forked the ipfire-2.x repo and successfully built the default
> image as a test (it took 3 hour(s) 52 minute(s) 55 second(s))!
> 
> Can anyone tell me how to build the pi image ?
> 
> Ozpoz
> _______________________________________________
> SIG-ARM mailing list
> SIG-ARM(a)lists.ipfire.org
> http://lists.ipfire.org/mailman/listinfo/sig-arm

jp1082 USB to Ethernet

[John Leake]

[-- Attachment #1: Type: text/plain, Size: 400 bytes --]

Hi All,
I have installed ipfire on my pi and all is ok except the very low cost
jp1082 USB to Ethernet adapters are not recognised.

I would like to build the jp drivers and include them in a pi ipfire SD
image.

I have forked the ipfire-2.x repo and successfully built the default
image as a test (it took 3 hour(s) 52 minute(s) 55 second(s))!

Can anyone tell me how to build the pi image ?

Ozpoz