I'll try as good as my influenca allows;)
I think, the problems came up with the change from 'select interface' in hostapd WUI to 'hostapd is on blue'.
BR, Bernhard
Am 17.10.2024 um 11:33 schrieb Michael Tremer:
Could you elaborate a little bit more on this?
We might want to fix this in c189 before other people walk into the same problem…
-Michael
On 16 Oct 2024, at 20:04, Bernhard Bitsch bbitsch@ipfire.org wrote:
Some light at the end of the tunnel. ;)
wlanap.cgi tries to set $INTF from $cgiparams{'INTERFACE'} in line 64. But $cgiparams{'INTERFACE'} is not defined or empty. Setting $INTF to "blue0" brings the channels and the status. I think there went something wrong with the modification to new look.
The problem with the kernel errors is solved by the interrupt setting.
Regards, Bernhard
Am 16.10.2024 um 18:20 schrieb Bernhard Bitsch:
I also cannot set the channel. Only automatic channel select available. /etc/init.d/hostapd restart functions at the second restart only. Messages: /etc/init.d/hostapd restart Stopping hostapd... [ Starting hostapd... blue0: interface state UNINITIALIZED->COUNTRY_UPDATE ACS: Automatic channel selection started, this may take a bit blue0: interface state COUNTRY_UPDATE->ACS blue0: ACS-STARTED Am 16.10.2024 um 17:05 schrieb Michael Tremer:
I believe this is a known bug in the driver. You can fix this by turning the IRQ mode to legacy. It is a setting of the module:
[root@fw01 ~]# modinfo ath10k_pci filename: /lib/modules/6.6.47-ipfire/kernel/drivers/net/ wireless/ath/ath10k/ath10k_pci.ko.xz firmware: ath10k/QCA9377/hw1.0/board.bin firmware: ath10k/QCA9377/hw1.0/firmware-5.bin firmware: ath10k/QCA9377/hw1.0/firmware-6.bin firmware: ath10k/QCA6174/hw3.0/board-2.bin firmware: ath10k/QCA6174/hw3.0/board.bin … parm: irq_mode:0: auto, 1: legacy, 2: msi (default: 0) (uint) …
This is most likely because of updating the firmware for your card.
-Michael
On 16 Oct 2024, at 16:02, Bernhard Bitsch bbitsch@ipfire.org wrote:
Hi,
since some time I noticed strange messages according to my WLAN card. With CU189 these are very frequently.
An extract from now:
... Oct 16 16:09:17 BitschCop kernel: ath10k_pci 0000:01:00.0: failed to increase tx pending count: -16, dropping Oct 16 16:10:39 BitschCop kernel: ath10k_pci 0000:01:00.0: failed to increase tx pending count: -16, dropping Oct 16 16:11:20 BitschCop kernel: ath10k_pci 0000:01:00.0: failed to flush transmit queue (skip 0 ar-state 1): 0 Oct 16 16:13:45 BitschCop kernel: ath10k_pci 0000:01:00.0: failed to increase tx pending count: -16, dropping Oct 16 16:18:47 BitschCop kernel: ath10k_pci 0000:01:00.0: failed to flush transmit queue (skip 0 ar-state 1): 0 Oct 16 16:18:52 BitschCop kernel: ath10k_pci 0000:01:00.0: failed to flush transmit queue (skip 0 ar-state 1): 0 Oct 16 16:19:13 BitschCop kernel: ath10k_pci 0000:01:00.0: failed to flush transmit queue (skip 0 ar-state 1): 0 Oct 16 16:19:28 BitschCop kernel: ath10k_pci 0000:01:00.0: failed to flush transmit queue (skip 0 ar-state 1): 0 Oct 16 16:19:33 BitschCop kernel: ath10k_pci 0000:01:00.0: failed to flush transmit queue (skip 0 ar-state 1): 0 Oct 16 16:19:38 BitschCop kernel: ath10k_pci 0000:01:00.0: failed to flush transmit queue (skip 0 ar-state 1): 0 Oct 16 16:19:43 BitschCop kernel: ath10k_pci 0000:01:00.0: failed to flush transmit queue (skip 0 ar-state 1): 0 Oct 16 16:19:48 BitschCop kernel: ath10k_pci 0000:01:00.0: failed to flush transmit queue (skip 0 ar-state 1): 0 Oct 16 16:19:54 BitschCop kernel: ath10k_pci 0000:01:00.0: failed to flush transmit queue (skip 0 ar-state 1): 0 Oct 16 16:19:59 BitschCop kernel: ath10k_pci 0000:01:00.0: failed to flush transmit queue (skip 0 ar-state 1): 0 Oct 16 16:20:04 BitschCop kernel: ath10k_pci 0000:01:00.0: failed to flush transmit queue (skip 0 ar-state 1): 0 Oct 16 16:20:09 BitschCop kernel: ath10k_pci 0000:01:00.0: failed to flush transmit queue (skip 0 ar-state 1): 0 Oct 16 16:20:24 BitschCop kernel: ath10k_pci 0000:01:00.0: failed to flush transmit queue (skip 0 ar-state 1): 0 Oct 16 16:20:40 BitschCop kernel: ath10k_pci 0000:01:00.0: failed to flush transmit queue (skip 0 ar-state 1): 0 Oct 16 16:21:10 BitschCop kernel: ath10k_pci 0000:01:00.0: failed to flush transmit queue (skip 0 ar-state 1): 0 Oct 16 16:21:16 BitschCop kernel: ath10k_pci 0000:01:00.0: failed to flush transmit queue (skip 0 ar-state 1): 0 Oct 16 16:21:41 BitschCop kernel: ath10k_pci 0000:01:00.0: failed to flush transmit queue (skip 0 ar-state 1): 0 Oct 16 16:21:46 BitschCop kernel: ath10k_pci 0000:01:00.0: failed to flush transmit queue (skip 0 ar-state 1): 0 Oct 16 16:21:51 BitschCop kernel: ath10k_pci 0000:01:00.0: failed to flush transmit queue (skip 0 ar-state 1): 0 ............
Regards, Bernhard
BTW: I'm missing the status part of the hostapd WUI page.