The patch which adjusts the options for IPFire in the libvirtd.conf does not apply in a newer version of libvirt. Creating this patch is harder than to use a separate config file.
This separate config file also enables us to adjust options much faster.
Signed-off-by: Jonatan Schlag jonatan.schlag@ipfire.org --- config/libvirt/libvirtd.conf | 501 ++++++++++++++++++ lfs/libvirt | 3 +- ...-options-in-libvirtd.conf-for-IPFire.patch | 35 -- 3 files changed, 503 insertions(+), 36 deletions(-) create mode 100644 config/libvirt/libvirtd.conf delete mode 100644 src/patches/libvirt/0002-Change-options-in-libvirtd.conf-for-IPFire.patch
diff --git a/config/libvirt/libvirtd.conf b/config/libvirt/libvirtd.conf new file mode 100644 index 000000000..dc4ba4cb6 --- /dev/null +++ b/config/libvirt/libvirtd.conf @@ -0,0 +1,501 @@ +# Master libvirt daemon configuration file +# + +################################################################# +# +# Network connectivity controls +# + +# Flag listening for secure TLS connections on the public TCP/IP port. +# NB, must pass the --listen flag to the libvirtd process for this to +# have any effect. +# +# This setting is not required or honoured if using systemd socket +# activation. +# +# It is necessary to setup a CA and issue server certificates before +# using this capability. +# +# This is enabled by default, uncomment this to disable it +listen_tls = 0 + +# Listen for unencrypted TCP connections on the public TCP/IP port. +# NB, must pass the --listen flag to the libvirtd process for this to +# have any effect. +# +# This setting is not required or honoured if using systemd socket +# activation. +# +# Using the TCP socket requires SASL authentication by default. Only +# SASL mechanisms which support data encryption are allowed. This is +# DIGEST_MD5 and GSSAPI (Kerberos5) +# +# This is disabled by default, uncomment this to enable it. +#listen_tcp = 1 + + + +# Override the port for accepting secure TLS connections +# This can be a port number, or service name +# +# This setting is not required or honoured if using systemd socket +# activation with systemd version >= 227 +# +#tls_port = "16514" + +# Override the port for accepting insecure TCP connections +# This can be a port number, or service name +# +# This setting is not required or honoured if using systemd socket +# activation with systemd version >= 227 +# +#tcp_port = "16509" + + +# Override the default configuration which binds to all network +# interfaces. This can be a numeric IPv4/6 address, or hostname +# +# This setting is not required or honoured if using systemd socket +# activation. +# +# If the libvirtd service is started in parallel with network +# startup (e.g. with systemd), binding to addresses other than +# the wildcards (0.0.0.0/::) might not be available yet. +# +listen_addr = "127.0.0.1" + + +################################################################# +# +# UNIX socket access controls +# + +# Set the UNIX domain socket group ownership. This can be used to +# allow a 'trusted' set of users access to management capabilities +# without becoming root. +# +# This setting is not required or honoured if using systemd socket +# activation. +# +# This is restricted to 'root' by default. +unix_sock_group = "libvirt-remote" + +# Set the UNIX socket permissions for the R/O socket. This is used +# for monitoring VM status only +# +# This setting is not required or honoured if using systemd socket +# activation. +# +# Default allows any user. If setting group ownership, you may want to +# restrict this too. +unix_sock_ro_perms = "0770" + +# Set the UNIX socket permissions for the R/W socket. This is used +# for full management of VMs +# +# This setting is not required or honoured if using systemd socket +# activation. +# +# Default allows only root. If PolicyKit is enabled on the socket, +# the default will change to allow everyone (eg, 0777) +# +# If not using PolicyKit and setting group ownership for access +# control, then you may want to relax this too. +unix_sock_rw_perms = "0770" + +# Set the UNIX socket permissions for the admin interface socket. +# +# This setting is not required or honoured if using systemd socket +# activation. +# +# Default allows only owner (root), do not change it unless you are +# sure to whom you are exposing the access to. +#unix_sock_admin_perms = "0700" + +# Set the name of the directory in which sockets will be found/created. +# +# This setting is not required or honoured if using systemd socket +# activation with systemd version >= 227 +# +#unix_sock_dir = "/var/run/libvirt" + + + +################################################################# +# +# Authentication. +# +# - none: do not perform auth checks. If you can connect to the +# socket you are allowed. This is suitable if there are +# restrictions on connecting to the socket (eg, UNIX +# socket permissions), or if there is a lower layer in +# the network providing auth (eg, TLS/x509 certificates) +# +# - sasl: use SASL infrastructure. The actual auth scheme is then +# controlled from /etc/sasl2/libvirt.conf. For the TCP +# socket only GSSAPI & DIGEST-MD5 mechanisms will be used. +# For non-TCP or TLS sockets, any scheme is allowed. +# +# - polkit: use PolicyKit to authenticate. This is only suitable +# for use on the UNIX sockets. The default policy will +# require a user to supply their own password to gain +# full read/write access (aka sudo like), while anyone +# is allowed read/only access. +# +# Set an authentication scheme for UNIX read-only sockets +# By default socket permissions allow anyone to connect +# +# To restrict monitoring of domains you may wish to enable +# an authentication mechanism here +#auth_unix_ro = "none" + +# Set an authentication scheme for UNIX read-write sockets +# By default socket permissions only allow root. If PolicyKit +# support was compiled into libvirt, the default will be to +# use 'polkit' auth. +# +# If the unix_sock_rw_perms are changed you may wish to enable +# an authentication mechanism here +#auth_unix_rw = "none" + +# Change the authentication scheme for TCP sockets. +# +# If you don't enable SASL, then all TCP traffic is cleartext. +# Don't do this outside of a dev/test scenario. For real world +# use, always enable SASL and use the GSSAPI or DIGEST-MD5 +# mechanism in /etc/sasl2/libvirt.conf +#auth_tcp = "sasl" + +# Change the authentication scheme for TLS sockets. +# +# TLS sockets already have encryption provided by the TLS +# layer, and limited authentication is done by certificates +# +# It is possible to make use of any SASL authentication +# mechanism as well, by using 'sasl' for this option +#auth_tls = "none" + + +# Change the API access control scheme +# +# By default an authenticated user is allowed access +# to all APIs. Access drivers can place restrictions +# on this. By default the 'nop' driver is enabled, +# meaning no access control checks are done once a +# client has authenticated with libvirtd +# +#access_drivers = [ "polkit" ] + +################################################################# +# +# TLS x509 certificate configuration +# + +# Use of TLS requires that x509 certificates be issued. The default locations +# for the certificate files is as follows: +# +# /etc/pki/CA/cacert.pem - The CA master certificate +# /etc/pki/libvirt/servercert.pem - The server certificate signed with +# the cacert.pem +# /etc/pki/libvirt/private/serverkey.pem - The server private key +# +# It is possible to override the default locations by altering the 'key_file', +# 'cert_file', and 'ca_file' values and uncommenting them below. +# +# NB, overriding the default of one location requires uncommenting and +# possibly additionally overriding the other settings. +# + +# Override the default server key file path +# +#key_file = "/etc/pki/libvirt/private/serverkey.pem" + +# Override the default server certificate file path +# +#cert_file = "/etc/pki/libvirt/servercert.pem" + +# Override the default CA certificate path +# +#ca_file = "/etc/pki/CA/cacert.pem" + +# Specify a certificate revocation list. +# +# Defaults to not using a CRL, uncomment to enable it +#crl_file = "/etc/pki/CA/crl.pem" + + + +################################################################# +# +# Authorization controls +# + + +# Flag to disable verification of our own server certificates +# +# When libvirtd starts it performs some sanity checks against +# its own certificates. +# +# Default is to always run sanity checks. Uncommenting this +# will disable sanity checks which is not a good idea +#tls_no_sanity_certificate = 1 + +# Flag to disable verification of client certificates +# +# Client certificate verification is the primary authentication mechanism. +# Any client which does not present a certificate signed by the CA +# will be rejected. +# +# Default is to always verify. Uncommenting this will disable +# verification - make sure an IP whitelist is set +#tls_no_verify_certificate = 1 + + +# A whitelist of allowed x509 Distinguished Names +# This list may contain wildcards such as +# +# "C=GB,ST=London,L=London,O=Red Hat,CN=*" +# +# See the POSIX fnmatch function for the format of the wildcards. +# +# NB If this is an empty list, no client can connect, so comment out +# entirely rather than using empty list to disable these checks +# +# By default, no DN's are checked +#tls_allowed_dn_list = ["DN1", "DN2"] + + +# A whitelist of allowed SASL usernames. The format for username +# depends on the SASL authentication mechanism. Kerberos usernames +# look like username@REALM +# +# This list may contain wildcards such as +# +# "*@EXAMPLE.COM" +# +# See the POSIX fnmatch function for the format of the wildcards. +# +# NB If this is an empty list, no client can connect, so comment out +# entirely rather than using empty list to disable these checks +# +# By default, no Username's are checked +#sasl_allowed_username_list = ["joe@EXAMPLE.COM", "fred@EXAMPLE.COM" ] + + +# Override the compile time default TLS priority string. The +# default is usually "NORMAL" unless overridden at build time. +# Only set this is it is desired for libvirt to deviate from +# the global default settings. +# +#tls_priority="NORMAL" + + +################################################################# +# +# Processing controls +# + +# The maximum number of concurrent client connections to allow +# over all sockets combined. +#max_clients = 5000 + +# The maximum length of queue of connections waiting to be +# accepted by the daemon. Note, that some protocols supporting +# retransmission may obey this so that a later reattempt at +# connection succeeds. +#max_queued_clients = 1000 + +# The maximum length of queue of accepted but not yet +# authenticated clients. The default value is 20. Set this to +# zero to turn this feature off. +#max_anonymous_clients = 20 + +# The minimum limit sets the number of workers to start up +# initially. If the number of active clients exceeds this, +# then more threads are spawned, up to max_workers limit. +# Typically you'd want max_workers to equal maximum number +# of clients allowed +#min_workers = 5 +#max_workers = 20 + + +# The number of priority workers. If all workers from above +# pool are stuck, some calls marked as high priority +# (notably domainDestroy) can be executed in this pool. +#prio_workers = 5 + +# Limit on concurrent requests from a single client +# connection. To avoid one client monopolizing the server +# this should be a small fraction of the global max_workers +# parameter. +#max_client_requests = 5 + +# Same processing controls, but this time for the admin interface. +# For description of each option, be so kind to scroll few lines +# upwards. + +#admin_min_workers = 1 +#admin_max_workers = 5 +#admin_max_clients = 5 +#admin_max_queued_clients = 5 +#admin_max_client_requests = 5 + +################################################################# +# +# Logging controls +# + +# Logging level: 4 errors, 3 warnings, 2 information, 1 debug +# basically 1 will log everything possible +# +# WARNING: USE OF THIS IS STRONGLY DISCOURAGED. +# +# WARNING: It outputs too much information to practically read. +# WARNING: The "log_filters" setting is recommended instead. +# +# WARNING: Journald applies rate limiting of messages and so libvirt +# WARNING: will limit "log_level" to only allow values 3 or 4 if +# WARNING: journald is the current output. +# +# WARNING: USE OF THIS IS STRONGLY DISCOURAGED. +#log_level = 3 + +# Logging filters: +# A filter allows to select a different logging level for a given category +# of logs. The format for a filter is one of: +# +# level:match +# level:+match +# +# where 'match' is a string which is matched against the category +# given in the VIR_LOG_INIT() at the top of each libvirt source +# file, e.g., "remote", "qemu", or "util.json". The 'match' in the +# filter matches using shell wildcard syntax (see 'man glob(7)'). +# The 'match' is always treated as a substring match. IOW a match +# string 'foo' is equivalent to '*foo*'. +# +# If 'match' contains the optional "+" prefix, it tells libvirt +# to log stack trace for each message matching name. +# +# 'level' is the minimal level where matching messages should +# be logged: +# +# 1: DEBUG +# 2: INFO +# 3: WARNING +# 4: ERROR +# +# Multiple filters can be defined in a single @log_filters, they just need +# to be separated by spaces. Note that libvirt performs "first" match, i.e. +# if there are concurrent filters, the first one that matches will be applied, +# given the order in @log_filters. +# +# A typical need is to capture information from a hypervisor driver, +# public API entrypoints and some of the utility code. Some utility +# code is very verbose and is generally not desired. Taking the QEMU +# hypervisor as an example, a suitable filter string for debugging +# might be to turn off object, json & event logging, but enable the +# rest of the util code: +# +#log_filters="1:qemu 1:libvirt 4:object 4:json 4:event 1:util" + +# Logging outputs: +# An output is one of the places to save logging information +# The format for an output can be: +# level:stderr +# output goes to stderr +# level:syslog:name +# use syslog for the output and use the given name as the ident +# level:file:file_path +# output to a file, with the given filepath +# level:journald +# output to journald logging system +# In all cases 'level' is the minimal priority, acting as a filter +# 1: DEBUG +# 2: INFO +# 3: WARNING +# 4: ERROR +# +# Multiple outputs can be defined, they just need to be separated by spaces. +# e.g. to log all warnings and errors to syslog under the libvirtd ident: +#log_outputs="3:syslog:libvirtd" + + +################################################################## +# +# Auditing +# +# This setting allows usage of the auditing subsystem to be altered: +# +# audit_level == 0 -> disable all auditing +# audit_level == 1 -> enable auditing, only if enabled on host (default) +# audit_level == 2 -> enable auditing, and exit if disabled on host +# +#audit_level = 2 +# +# If set to 1, then audit messages will also be sent +# via libvirt logging infrastructure. Defaults to 0 +# +#audit_logging = 1 + +################################################################### +# UUID of the host: +# Host UUID is read from one of the sources specified in host_uuid_source. +# +# - 'smbios': fetch the UUID from 'dmidecode -s system-uuid' +# - 'machine-id': fetch the UUID from /etc/machine-id +# +# The host_uuid_source default is 'smbios'. If 'dmidecode' does not provide +# a valid UUID a temporary UUID will be generated. +# +# Another option is to specify host UUID in host_uuid. +# +# Keep the format of the example UUID below. UUID must not have all digits +# be the same. + +# NB This default all-zeros UUID will not work. Replace +# it with the output of the 'uuidgen' command and then +# uncomment this entry +#host_uuid = "00000000-0000-0000-0000-000000000000" +#host_uuid_source = "smbios" + +################################################################### +# Keepalive protocol: +# This allows libvirtd to detect broken client connections or even +# dead clients. A keepalive message is sent to a client after +# keepalive_interval seconds of inactivity to check if the client is +# still responding; keepalive_count is a maximum number of keepalive +# messages that are allowed to be sent to the client without getting +# any response before the connection is considered broken. In other +# words, the connection is automatically closed approximately after +# keepalive_interval * (keepalive_count + 1) seconds since the last +# message received from the client. If keepalive_interval is set to +# -1, libvirtd will never send keepalive requests; however clients +# can still send them and the daemon will send responses. When +# keepalive_count is set to 0, connections will be automatically +# closed after keepalive_interval seconds of inactivity without +# sending any keepalive messages. +# +#keepalive_interval = 5 +#keepalive_count = 5 + +# +# These configuration options are no longer used. There is no way to +# restrict such clients from connecting since they first need to +# connect in order to ask for keepalive. +# +#keepalive_required = 1 +#admin_keepalive_required = 1 + +# Keepalive settings for the admin interface +#admin_keepalive_interval = 5 +#admin_keepalive_count = 5 + +################################################################### +# Open vSwitch: +# This allows to specify a timeout for openvswitch calls made by +# libvirt. The ovs-vsctl utility is used for the configuration and +# its timeout option is set by default to 5 seconds to avoid +# potential infinite waits blocking libvirt. +# +#ovs_timeout = 5 diff --git a/lfs/libvirt b/lfs/libvirt index 882aa7c8d..bdfd2e4af 100644 --- a/lfs/libvirt +++ b/lfs/libvirt @@ -78,7 +78,6 @@ $(TARGET) : $(patsubst %,$(DIR_DL)/%,$(objects)) @$(PREBUILD) @rm -rf $(DIR_APP) && cd $(DIR_SRC) && tar Jxf $(DIR_DL)/$(DL_FILE) cd $(DIR_APP) && patch -Np1 -i $(DIR_SRC)/src/patches/libvirt/0001-Change-default-behavior-of-libvirt-guests.sh-for-IPF.patch - cd $(DIR_APP) && patch -Np1 -i $(DIR_SRC)/src/patches/libvirt/0002-Change-options-in-libvirtd.conf-for-IPFire.patch cd $(DIR_APP) && ./configure --prefix=/usr --localstatedir=/var --sysconfdir=/etc \ --with-openssl --without-sasl \ --without-uml --without-vbox --without-lxc --without-esx --without-vmware --without-openvz \ @@ -95,5 +94,7 @@ $(TARGET) : $(patsubst %,$(DIR_DL)/%,$(objects)) mv /usr/libexec/libvirt-guests.sh /etc/rc.d/init.d/libvirt-guests # Backup install -v -m 644 $(DIR_SRC)/config/backup/includes/libvirt /var/ipfire/backup/addons/includes/libvirt + # Install libvirtd.conf + cp -fv $(DIR_SRC)/config/libvirt/libvirtd.conf /etc/libvirt @rm -rf $(DIR_APP) @$(POSTBUILD) diff --git a/src/patches/libvirt/0002-Change-options-in-libvirtd.conf-for-IPFire.patch b/src/patches/libvirt/0002-Change-options-in-libvirtd.conf-for-IPFire.patch deleted file mode 100644 index ff6cb629a..000000000 --- a/src/patches/libvirt/0002-Change-options-in-libvirtd.conf-for-IPFire.patch +++ /dev/null @@ -1,35 +0,0 @@ -From 69d6e8ce6c636f78d1db0eebe7fb1cc02ae4fb9a Mon Sep 17 00:00:00 2001 -From: Jonatan Schlag jonatan.schlag@ipfire.org -Date: Mon, 6 Jun 2016 19:40:50 +0200 -Subject: [PATCH 2/2] Change options in libvirtd.conf for IPFire - -Signed-off-by: Jonatan Schlag jonatan.schlag@ipfire.org - ---- a/src/remote/libvirtd.conf~ 2018-10-24 09:12:31.045030419 +0100 -+++ b/src/remote/libvirtd.conf 2018-10-24 09:12:33.443109098 +0100 -@@ -82,14 +82,14 @@ - # without becoming root. - # - # This is restricted to 'root' by default. --#unix_sock_group = "libvirt" -+unix_sock_group = "libvirt-remote" - - # Set the UNIX socket permissions for the R/O socket. This is used - # for monitoring VM status only - # - # Default allows any user. If setting group ownership, you may want to - # restrict this too. --#unix_sock_ro_perms = "0777" -+unix_sock_ro_perms = "0770" - - # Set the UNIX socket permissions for the R/W socket. This is used - # for full management of VMs -@@ -99,7 +99,7 @@ - # - # If not using PolicyKit and setting group ownership for access - # control, then you may want to relax this too. --#unix_sock_rw_perms = "0770" -+unix_sock_rw_perms = "0770" - - # Set the UNIX socket permissions for the admin interface socket. - #