Hi Michael,
as i said all nics are shown, even in ip link:
1: lo: mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 2: eth0: mtu 1500 qdisc fq_codel master red0 state DOWN mode DEFAULT group default qlen 1000 link/ether 00:90:7f:41:2d:25 brd ff:ff:ff:ff:ff:ff 3: eth1: mtu 1500 qdisc fq_codel master red0 state DOWN mode DEFAULT group default qlen 1000 link/ether 00:90:7f:41:2d:24 brd ff:ff:ff:ff:ff:ff 4: eth2: mtu 1500 qdisc fq_codel master red0 state DOWN mode DEFAULT group default qlen 1000 link/ether 00:90:7f:41:2d:23 brd ff:ff:ff:ff:ff:ff 5: green0: mtu 1500 qdisc fq_codel state UP mode DEFAULT group default qlen 1000 link/ether 00:90:7f:41:2d:22 brd ff:ff:ff:ff:ff:ff 6: eth4: mtu 1500 qdisc fq_codel master red0 state UP mode DEFAULT group default qlen 1000 link/ether 00:90:7f:41:2d:21 brd ff:ff:ff:ff:ff:ff 7: eth5: mtu 1500 qdisc fq_codel master red0 state DOWN mode DEFAULT group default qlen 1000 link/ether 00:90:7f:41:2d:20 brd ff:ff:ff:ff:ff:ff 8: eth6: mtu 1500 qdisc fq_codel master red0 state DOWN mode DEFAULT group default qlen 1000 link/ether 00:90:7f:41:2d:1f brd ff:ff:ff:ff:ff:ff 9: eth3: mtu 1500 qdisc fq_codel master red0 state DOWN mode DEFAULT group default qlen 1000 link/ether 00:90:7f:41:2d:1e brd ff:ff:ff:ff:ff:ff 10: red0: mtu 1500 qdisc fq_codel state UP mode DEFAULT group default link/ether 00:90:7f:41:2d:1e brd ff:ff:ff:ff:ff:ff
There ist no scroll bar in the setup. Also if you try to scroll down nothing happens. setup.log is empty
Since i'm running Core 100 (fresh embedded install), the limitation doesnt seem to be fixed.
I'm attaching an setup screenshot to your private mail.
regards sash
-----Ursprüngliche Nachricht----- Von: Michael Tremer Gesendet: Do. 28.04.2016 19:25 An: g6094199@freenet.de, development@lists.ipfire.org Betreff: Re: Possible configuration bug with >6 nics
Hello,
there was a limit prior to Core Update 100 but this should have gone away and actually 20 NICs should be shown by now.
Did you try to scroll down? Are there any errors shown?
What is the output of "ip link"?
Best, -Michael
On Thu, 2016-04-28 at 16:52 +0200, g6094199@freenet.de wrote:
He guys!
i recently installed IPFire core 100 to an Watchguard Firebox X 750e/1000e. All installed to an CF-card, booted up fine. Came to the general setup and asked to map the nics to an interface. While the x750 has 8 nics (4x Marvell 88E8001, 4x 88E8053) only 6 nics are shown in the setup menue via serial port. which seems to be a limitation by the GUI or a bug.
I can see als of the interfaces on cli after i finished the initial setup
lspci: 01:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8053 PCI-E Gigabit Ethernet Controller (rev 19) 02:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8053 PCI-E Gigabit Ethernet Controller (rev 19) 03:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8053 PCI-E Gigabit Ethernet Controller (rev 19) 04:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8053 PCI-E Gigabit Ethernet Controller (rev 19) 05:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8001 Gigabit Ethernet Controller (rev 13) 05:01.0 Ethernet controller: Marvell Technology Group Ltd. 88E8001 Gigabit Ethernet Controller (rev 13) 05:02.0 Ethernet controller: Marvell Technology Group Ltd. 88E8001 Gigabit Ethernet Controller (rev 13) 05:03.0 Ethernet controller: Marvell Technology Group Ltd. 88E8001 Gigabit Ethernet Controller (rev 13)
I also can use them. So it seems to be a limitation/bug of the setup menue?!
Any thoughs?
regards sash
Mail & Cloud Made in Germany mit 3 GB Speicher! Jetzt kostenlos anmelden>
-----Ursprüngliche Nachricht Ende----
--- Alle Postfächer an einem Ort. Jetzt wechseln und E-Mail-Adresse mitnehmen! https://email.freenet.de/mail/Uebersicht?epid=e9900000451
